Hi all - looking for some quick advice and all opinions welcomed!
Question: Is it really possible for a 3 year old new build flat Ideal Combi 35 to have "Multiple component failure due to poor water quality - drain down & powerflush required to inhibit future related issues, which are now...
Hi,
The boiler is not working and there is currently no hot water and it is not turning on..F1 message has flagged up and I have read around that this means that the pressure is low..checked the pressure gauge and it is at 1.7? I'm not sure what is happening! If the pressure gauge is okay then...
Hi,
My boiler is dripping as an be see in the picture below the right hand screw, as anyone seen this leak on this boiler before and resolved the problem?.
Thanks
Hi all, obviously I am new here and just looking for a bit of advice.
I recently had a new Ideal Logic + Combi 30 boiler fitter which I am very happy with. However, the boiler is in summer mode and with no demand on it, it goes through a burner and purge cycle every 30min. This does not seem...
Hi. New to this forum.
can someone advise on the average cost of the above boiler with fitting. Have to de commission old boiler upstairs and put new one in kitchen with all new fittings.
have been given a quote of 2300 for this in a 3 bed house.
feel this is very expensive as have been given...
Shank
Thread
boiler
check
combi
given
idealidealcombi
logic
plus
quote
I have an Ideal combi 24 that's 5 years old. This winter I noticed that the (non digital) clock is often slow. It started with a few minutes every day and is now on 30mins in 24hrs. It's easy enough to reset the clock every day, but still annoying when I forget and the heating doesn't come on in...
A client has sent me a couple of the above boiler. Once the heating comes on, it stays on. Am not sure what boiler it is but you guys will probably tell by the controls. It has a cm927 wireless stat to it. Are there common faults I should be looking for with this boiler? Stuck diverter valve...
About 2 weeks ago i got up in the morning and found the boiler was not working and the display said 'F1'. I Googled the code and what i read was easy no problem, the gauge was showing 0 pressure, so open up black and blue values until pressure rose to 1.5 bar, closed them and system fired back...
efc84
Thread
code
combi
error
error code
idealidealcombi
pressure
still
system
Hi,
I've been having problems with my Ideal Combi HE30 boiler for a few months now (as have many others by the looks of it!)
Firstly the PCB went in June, so I called out British Gas and they replaced it. It was fine for a month or so, then every fifteen minutes the heating appeared to click...
Blossom21
Thread
boiler
british
combi
could
every
he30
idealidealcombi
problem
Was on a job doing a H/A boiler change today and the old boiler was an ideal combi(never noted model) but was a condesing combi. When first saw appliance i noticed what i would describe as black scorch/soot marks on the yellow walls around the appliance. I noticed no I.D badge on appliance and...
gaspastemania
Thread
appliance
around
boiler
combiidealidealcombi
marks
never
Got the above mini c32 ideal boiler .Connected to 9 Rads & running it on 1 bar pressure but, when i push the heating up to under 1/2 the pressure willris to 3 !! Iunderstand it should be lower than 2 . therefore i can never run it on 2/3 or max heat ! :confused:
sided
Thread
boiler
change
combicombi boiler
expansion
idealidealcombi
mini
oil
original
pressure
vessel
today did a new gas run ,customer asked to reconnect existing gas appliances i refused to do it as !gas hob did not have isolating valve ,sign of burn on taps ,primary air port partly block with sh''''t ignition button missing!so ID i thought
boiler flue less then 300 mm from internal...
air
baxi
boiler
burst
button
combi
concrete
condensing
electric
flue
gas
gas pipe
gas supply
idealidealcombi
ignition
kitchen
ncs
pipe
primary
supply
taps
valve
work
I have an Ideal Combi Boiler and most of the radiators are new, just recently although the boiler is showing 0 - off and the thermostat is also on off position. Any advice would be appreciated.
Michelle H
Thread
boiler
central
central heating system
combicombi boiler
control
idealidealcombi
oil
radiators
HELP ME!!
- I have just moved into a new house and we have an Ideal combi boiler and a CM921 honeywell wireless thermostat. _ I have no idea if this is working properly and the installation guide is not much help... I need to find a plumber in the Chingford area to check the system and give me...
Kerry J
Thread
boiler
central heating system
combicombi boiler
find a plumber
guide
honeywell
idealcombi
installation
manual
plumber
switch
system
website
wireless
work
Hi, what temp should hot water be set to on combi boiler? also if the flow is to high for the requested water temp does turning up the temp settings have any effect or does the boiler automaticaly use full power to try and achevie the temp? my boiler is a ideal combi logic+
duarab
Thread
boiler
cold
combicombi boiler
flow
high
hot
hot water
idealcombi
power
temp
temperature
water
winter
Hi All
just wondering if anyone has had any problems with the Ideal logic so far. I have fitted half a dozen this year and so far had no call backs. with the reputation ideal have im waiting for the bubble to burst.
anyone else out there had any problems.
derrybongo
Thread
boiler
burst
central heating system
combi
condensing
control
electronic
flow
gas
high
icos
idealidealcombiideal logic
installers
jobs
logic
merchant
merchants
plumber
radiator
radiators
screen
stock
trv
Help wanted for ideal mini C24 combi
heating fine no problems
demand for hot water the following happens:
DHW flow switch activates pin operates micro switch ok
the boiler flow switch (sometimes called the ch switch) is not operating
the pin does not operate the mico switch, when the mico switch...
paul H
Thread
boiler
boilers
central heating system
dhw
diverter valve
flow
hot
hot water
idealidealcombi
job
mini
moving
no hot water
power
pump
radiators
switch
system
valve
water
I have an Isar Ideal combi boiler. I recently started draining the central heating system down to remove and refit a radiator on the ground level of a house. The water drained as expected, but after a short while began to run hot, despite the fact the central heating was switched off. Upon...
wmbmrg
Thread
boiler
central
central heating system
combicombi boiler
connection
cross
dhw
electric
expansion
filling loop
hot
hot water
idealcombi
mains
no hot water
oil
pipes
problem
radiator
radiators
remove
supply
system
taps
water
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.