You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
hob
Hobbing is a machining process for gear cutting, cutting splines, and cutting sprockets on a hobbing machine, which is a special type of milling machine. The teeth or splines of the gear are progressively cut into the material (a flat, cylindrical piece of metal) by a series of cuts made by a cutting tool called a hob. Compared to other gear forming processes it is relatively inexpensive but still quite accurate, thus it is used for a broad range of parts and quantities.It is the most widely used gear cutting process for creating spur and helical gears and more gears are cut by hobbing than any other process as it is relatively quick and inexpensive.A type of skiving that is analogous to the hobbing of external gears can be applied to the cutting of internal gears, which are skived with a rotary cutter (rather than shaped or broached).
Hi all,
Having started on the screwfix website and noted that many of the gas discussions were taking place in the plumbing forum, I thought I'd come back to the site that has helped me greatly so far.
We currently have a freestanding LPG gas cooker connected via a flexible hose. We are moving...
hi
i have gas registered recently and i did gas safety check for hobs but there was hob plate missing. the engineer who have done last year described it as ncs. but what i think is it is not safe to use. ar?
please advise for me
Hello,
I have purchased a Calor Gas Cooker Hose kit TB 1053) and a automatic changeover kit (TB 1029) together with a 6m length of yellow Kuterlex tube 15mm * 0.7mm
The pipe needs to be run down a wall outside and buried for approx. 3ft. then run up an outside wall and in the house. The hole...
oddball
Thread
bottles
engineer
gas
gas engineer
gas safe register
gsr
hob
install
lpg
safety
Does anyone have an updated copy of these thy don't mind sharing???? I can't seem to find them on the line... I was researching about gas connections to hobs which on this thread:
http://www.ukplumbersforums.co.uk/gas-safe-register-forum-public-forum/16676-gas-hob-flexy-4.html
states it can be...
Hello,
In fear of having the wool pulled over my eyes, can somebody who can quote the reg. please comment on the following:
Ive just installed a new kitchen, the worktop has been cut for a gas hob. the outlet is on a valve, with a G1/2 Male connection, the hob also has a G1/2 male...
Fitted a hob today built in electric oven.
The old hob connection was further back than connection on the new beko one so after trying 20 different pipe combos the oven still wont go in flush as its hitting the connection
any advice as I've never had one cause this much bother :confused5:
Wheres good for hob fittings.
Had a few where theres just a male and no iron elbow included.
Sent off for a few from Hamiltons in ireland as the local suppliers are a shower of $€£¥.
After a 1/2 flat face female onto a 10mm or 15mm compression similar to this.
Good morning all,
I am writing here because I have just moved to a new flat which I am renting. It is a two bedroom flat, I rent one of the room and share the flat with one flatmate.
I have checked the gas hob and it does not have a safety valve. I have usually lived in homes where the hob...
Ste_Vege
Thread
gas
hob
landlord
safety
safety valve
valve
without
Wasn't sure where to post this but hoping a gas safe man reads it...
I've got a gas hob and when the weather is hot the gas supply to it exhibits some strange characteristics. In hot weather, when you turn the gas knob for any of the rings to ON, and light it, the gas surges through quite...
Guys, A tight customer is paying a fortune for some new granite worktops , he wont pay for a new hob lol
( he probably has no money left ) anyway the old hobs going back in , asuming the original seal cant be reused , would you use some high temp silicone to make the new seal .
Thank you .
I am looking to have a Worcester Bosch compact fitted in my kitchen cupboard as per below.
Imagine if I to the right of the boiler was an extractor and on the worktop there was a gas hob. Would this be allowed?
A guy I had round today said it wouldn't be allowed as the boiler is plastic and...
Hi all,
how much do you normally charge to install rigid piping from bayonet fitting to hob?
The hob is already installed in place
Also, where should the isolation valve be located as I'm sure it probably needs to be somewhere easily accessible behind the base unit doors and not be behind...
went to have a look at a gas hob today. flame picture slightly unstable and slight impingement on 2 of the burners - injectors clean etc and supply was fine - any ideas what else?
cheers
Hello,
Last year we got a new kitchen fitted and we got a Bosch Hob (model PPP616B91E). It works ok but the big burner sometimes won't start (I need to keep the button down for > 5 sec, or stop and start again several times) and when it does it's a huge flame which I find very scary! (I...
Primrose
Thread
bosch
hob
problem
problems
starts
times
under
warranty
Got both the above items for sale, here is a link to both of them, cheers
Indesit Pim640Asix Pim640As Built In Gas Hobs In Stainless Steel | eBay
Indesit FIM33KAIX Fanned Electric Built In Single Oven With Timer | eBay
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.