Search the forum,

Recent content by lupieloo

  1. L

    Geberit aco 103 plus press tool advice.

    Think I better ring REMS and don't want to spend £300+ on attachments that don't fit.
  2. L

    Geberit aco 103 plus press tool advice.

    Hi. I've recently purchased a press tool which is branded geberit but it's actually a novopress aco 103. I was wondering if anyone knew if there was an adaptor that would fit so I can get the machine in tight spaces. I know Rems do a 45° attachment but not sure if this would fit in my...
  3. L

    Telford tempest cylinder fault?

    Hi I have a Telford tempest unvented cylinder and I'm finding that when the hot water is on and I turn it off on the programmer the TPRV opens and let's the hot water out. Only stops running when it cools down again. What I find strange is that it only happens if I turn the programmer off. If...
    • lupieloo
    • Thread
    • america cylinder fault telford usa
    • Replies: 1
    • Forum: USA
  4. L

    Viessmann vitodens 100 FF fault?

    Yes I'll ring them Tuesday tried to call while on site but obviously not open so I'll ask them then. I'll let you know what the outcome is. Thanks
  5. L

    Viessmann vitodens 100 FF fault?

    Hi. I've been out to look at this boiler today (I am a gas engineer) and found that this FF fault code keeps coming up even after restarting the boiler. On arrival I found pressure was on zero so I topped it back up and reset the boiler. On the display it says 141 then changes to...
    • lupieloo
    • Thread
    • america fault usa viessmann vitodens
    • Replies: 2
    • Forum: USA
  6. L

    showermax supercal cylinder

    No nothing is off and not that I know off. I'll take the shower off and let the water run out through the pipe see what that does. Then I can eliminate if it's the shower.
  7. L

    showermax supercal cylinder

    The flow is really good so I can't understand why it's not getting hot or staying hot. It's indirect cylinder. What could be the cause? I might take the shower off and see if hot water comes out constant. I've turned the cold feed off to the shower and left the hot on and the flow is really...
  8. L

    showermax supercal cylinder

    I'm not sure I haven't worked on one before but the showers been working for years and it's had the cartridge replaced etc so I'm not sure what the problem is. How does the mains feed through the cylinder work as I'd imagine if it runs through a coil it wouldn't have time to heat the water to...
  9. L

    showermax supercal cylinder

    Hi I've been out to look at this job where this cylinder has been installed for over 15yrs now. Hot water works fine on the gravity fed side but the mains going through the cylinder for the shower feed doesn't stay hot. It will last a few seconds then runs cold. Is there a fault inside the...
  10. L

    Glowworm 30cxi f12 fault code?

    Main printed circuit board gone. Test connection J13 on connection 6 to earth if there is no or not much voltage it's the main board. Kind Regards
  11. L

    Glowworm 30cxi f12 fault code?

    I tried ringing them around 6pm yesterday and they were close even though on there website it states 7pm closing. Suppose that's glowworm for you. Ill let you know what I find but I think it's the display board too I just need to 100% make sure before I buy. Kind Regards
  12. L

    Glowworm 30cxi f12 fault code?

    Hi. I'm currently working on repairing this boiler. What are the most common faults with f12 error code? When turning the boiler on it reads 0.0bar and I can hear the fan constantly running but nothing else the goes to f12. After a while it will then come off f12 and fire up. This...
  13. L

    Ideal isar 30he

    Hi Servicing this boiler and I have found the inlet working pressure is 12-13mbar when hot tap is running. At the meter is 24mbar working. 26mbar standing. Would this be classed as At risk? Ideal has mentioned it would be as it would cause incomplete combustion. Anything below 14mbar...
  14. L

    Baxi combi 105he fault.

    Yes think it might be the pcb. She reset it but I need to check resistance on the fan and continuity on the air pressure switch. I'll let you know what it is.
  15. L

    Baxi combi 105he fault.

    Yes ignites fine when resetting. Power to fan 230v. Power to air pressure switch 160v is that correct?
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock