ideal logic

Went to service logic heat 15 today with complaint of L2 showing and having to reset to get it going . Hadn't been serviced in five years from new ... The heat exchanger and siphon were gunged up with aluminium oxide sediment , cleaned thoroughly., cleaned spark and sensor probes ,checked flow...

Hi all, New to the forum. Last night, while running hot water from our Logic Combi 35 boiler the front display started displaying F-1 and stopped producing any hot water. Of course this usually means low pressure, however the gauge is showing 2.5Bar. There is plenty of pressure at the hot...

Can the ideal logic gas valves be adjusted? Couldn't see anything in the manual. I've got one to go to that's making a baffling noise.

Anyone know what causes the Logic range to go to F9 fault, MI's just say PCB fault-replace PCB. Serviced a 24+ Heat today, 1 year old. Carried out the service, fired it up and ran through FGA checks etc. Tidied up and was talking to the customer and noticed the F9 showing. Wouldn't reset...

Hi guys had this boiler tonight. Hw pressure is terrible at all outlets. Cold is fine. had a bit of orangey water come out the bath taps. Stopcock has been off to change a scale reducer on mains up to boiler in the loft. Not by me. Cust is an idiot, trying to tell me where there is a...

Hi I'm just wondering of anyone can help. I've moved into my first flat (which I rent) two months ago and it has an Ideal Logic combi + boiler. I've had problems with getting hot water, especially in the kitchen hot tap where sometimes the boiler doesn't even light when I turn it on. When...

Hi Wendy here sorry but I am very new to heating, I have an ideal logic eat 15 installed less than 2 yrs ago, I was getting f&d showing and got out th engineers, they replaced a water flow sensor but it still did not work, thay said I need to bleed the radiators and if that did not work then I...

Hi - our boiler was installed almost two years ago and is due it's 2nd yearly service under the warranty. Ryan at Universal Gas Works installed this for us and has previously serviced it but due to his schedule and our location he can't do it this year and suggested I post the job to the forum...

I need to ask a customer to tell me the serial number for the above boiler but I can't remember where the Data badge is located on these boilers, the manual just says its on the front cover but I need to be a bit more specific as I will be asking on the phone. Can someone that installs these a...

Ideal Logic Plus 35 or Ideal Independent Plus 35? - both fit into the existing boiler space so which one would you recommend?. Am I right in saying that internally thiese are identical and the only difference is in the outer casings? Is the price difference worth it and if so -why? 2. Best...

A short while ago my heating stopped working. The engineer came out twice and said that some type of connection was not being made between some box upstairs (that only has a green or red light on it) and the temperature gauge downstairs in the hallway. He said that this meant something wasn't...

Hello all, I've just had an ideal logic plus 30 installed in my loft, replacing an existing vented system. The boiler works fine, until you put the front outer cover on, then it fires for a short time and cuts out on flame failure, remove the cover and it works perfectly? I understand that it...

Called to a Ideal logic heat 15 with FA fault code flashing. S plan on unvented. System is 3 or so years old and had been working fine up until then. FA code says flow return crossed. But its been working fine till now. Any ideas ????

Hi, I have had an Ideal logic 24 in my flat for about 4 years. In the last month or 2 it has started needing the pressure topping up every 2 days. Its under warranty so Ideal came out and replaced the flow turbine, sump, heat exchanger and svalve but without any difference seen. We've not...

Hi, We have a 3 year old ideal logic + system which to date has been very good. Last night it flashed an F1 fault, which is normally to add water pressure, so i added some via the filling loop and watched the gauge increase, it then kicked in reporting a "c" status and burner light BUT 10...

just installed one today. great boilers to fit must say. just one thing i noticed with it when i came to analyse it was the ratio was 0.0015. i know its below the trigger value, but it just seems high for new install. fitted the heat only version other day and ratio was 0.0002. are the combi...

hi guys, installing one of these tomorrow. 1 problem i have is i wanted the high level flue oulet, but they only supplied standard rear flue. can i install the standard one and just change out the flue exit. i would just wait but they cant get me the plume kit till thursday and it stops me...

Hi there, got quoted £1450 for replacing ancient combi with an Ideal Logic+ 30 (7 Yr Warranty) extended flue, wireless thermostat, fernox flush, associated brick & pipework, certificate & commissioned, from a locally well respected Gas Safe chap... What do we think??

I only really do Installs so breakdowns is something I need help with, I'm going to go and have a look at an Ideal Logic 35 that is having problems with the hot water. The heating is working fine, however when hot water is needed sometimes the boiler fires up other times it doesn't, the boiler...

Had to replace the condensate sump on this only 2.5yrs old, cust neighbours some have also had it done. When I phoned ideal for part number, I explained I had a leak, they told me what the leak was and part number before I had even explained it! Thought ideal were getting better?