Users can remove all display ads (not sponsors) for a small fee. Click for info (must be logged in)

Recent content by Uheat – Wojtek

  1. U

    Mixer valve set up not controlling temperature

    Hi there, as you've said - looks like the mixing valve doesn't do anything. I've done some research and I think replacing your mixing valve with Esbe VTA232 will be the best option. It has to be the 323 version as it will have flow, return and mixed water at correct ends. You might need to...
  2. U

    Flow and return the wrong way around

    I haven't I'm afraid.
  3. U

    Flow and return the wrong way around

    Good morning, I don't think the actuators became damaged but you never know. Pump - same again, difficult to judge. Flow rates - they will depends on circuit lengths. Many thanks, Uheat – Wojtek
  4. U

    Flow and return the wrong way around

    I think is a Polypipe manifold. It doesn't make any difference to be honest, you can swap the bars around anyway. Thanks, Uheat – Wojtek
  5. U

    Flow and return the wrong way around

    Good afternoon, it looks like a Polypipe manifold to me which has got the flow meters at bottom bar. The control pack is not Polypipe, looks like Rifeng Inta Eco Ecomix. What you need to do unscrew the manifold bars from the brackets and swap them so flow meters will be at the top of the...
  6. U

    Problem with UF Heating Heatmiser Thermostats

    Hi there, it sounds very strange. We supply Heatmiser controls since few years to be honest we hardly got any problems with them. Have you been asked to return them to your supplier so they could send them back to Heatmiser for testing? Heatmiser will take them into the pieces and check what...
  7. U

    Manifold identification

    Hi Steve@smv, I don't recognise the brand of the manifold I'm afraid. It's not very easy to find right pin valve as they might have a different foot/plunger at the bottom, or different thread pitch and the whole valve lenght could be different. If you would have a chance to remove one and post...
  8. U

    Thumping manifold, bouncing flow meter

    Hi Wayne, does it just happen to one flow meter? I've had a customer week ago with exactly the same symptoms at Uponor manifold. He replaced the flow meters and the noise is gone. Thanks
  9. U

    Thumping manifold, bouncing flow meter

    Hi Wayne, does it just happen to one flow meter? I've had a customer week ago with exactly the same symptoms at Uponor manifold. He replaced the flow meters and the noise is gone. Thanks
  10. U

    help plz

    Hi guys, sorry about the delay in replying. drewbigun1 if you would like me to have a look at the desing please email it to me and I'll have a look at it. Thanks a lot
  11. U

    help plz

    Hi guys, sorry about the delay in replying. drewbigun1 if you would like me to have a look at the desing please email it to me and I'll have a look at it. Thanks a lot
  12. U

    Myson Actuator Issues

    Hi Robaxter02, you are correct, looks like an actuator is gone. The reason why there's so warm now in that room is because there's no actuator to restrict the flow to that circuit. Please let me see the photo of your manifold and I'll see if I can supply an actoatur for you.
  13. U

    Electric underfloor heating

    Hello everyone, Steve, we do 6mm XPS polystyrene boards which can be installed by using 1-2 mm flexible tile adhesive. Heating mat goes on top. I totally understand you don't want to have a little step but if you use the insulation boards we know the UFH will work and will be more efficient and...
  14. U

    Can any boy help ?/ want the job?!!

    Good afternoon everyone, I'm got a good installer not far from you (less than 20 miles). Please give him a call and mention you have got a number from Wojtek @ Uheat. MIP Heating Peter 07917 728333 If we won't have a time to do it he should be able to give you someone else number. Hope that...
  15. U

    pexathem U/F Heating spares

    Hi there, they might be standard size so you might be able to use different manufacturers. I would try this company: Pexatherm Underfloor Heating Systems It looks like they supply Paxatherm manifolds so they might have some spares. I'll be away next week so I would like to wish a Merry...

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock