Recent content by Moffski72

  1. M

    Sealing Back to Wall Pan

    Just spray it wit soapy water then use whatever device u like to remove excess silicone...Lidl do some really good silicone tools...
  2. M

    Position of a AECV entering property

    Ok maybe I should stop drinking gin... That might possibly be an earth cable....
  3. M

    Position of a AECV entering property

    Ha! And I suppose the the garden hose is a purge line...
  4. M

    Position of a AECV entering property

    Let's hope the gas is the 15mm in the middle...otherwise...., But yeah, aecv needs to be accessible otherwise what's the point? If the boiler is the only appliance, then an aecv prob isn't even necessary, considering where it's going to go...
  5. M

    How can this kitchen tap be replaced?

    Or...https://www.NoLinkingToThis/p/rothenberger-monoblock-tap-spanner-set/40102 :D
  6. M

    ideal eyesore.......

    Are they? Why am I not surprised. Ok, ta, I'll give it a go:D
  7. M

    ideal eyesore.......

    Thanks for this, I'll check it, but I've let it modulate right down, cut out and cut back in again and I cannot get it to replicate the fault. I've turned up at the property and seen the lf fault on the display, but I can't get it to perform when I'm there. Feel a bit like throwing a board at...
  8. M

    ideal eyesore.......

    Ok...why? I know it's cheap and would rule somethin else out, but then I'm just going down the elimination route, and I hate that route... Although I'm starting to think it would be better just to change it for something, now what's the word....? Oh yeah, less horrific and more, you know...
  9. M

    ideal eyesore.......

    Yeah checked that out as well, took the old one off and checked continuity while wiggling lead about, was iffy with old electrode connected, put new electrode on lead and all was fine and dandy. I've had em where the lead has actually disintegrated when move about, so yeah I know about that...
  10. M

    ideal eyesore.......

    Morning chaps. Got an issue with and ideal istor, would appreciate your thoughts on? Customer (rented) keeps reporting to his landlord that he has to reset the boiler every couple of hours.(l-f fault so flame loss) First time I looked at it, had leaks every bloody where, so changed a few bits...
  11. M

    Mira mode mixer shower issue...maybe....

    They've got feckin gremlins then... OK, cheers for replies
  12. M

    Mira mode mixer shower issue...maybe....

    Eh? Why would they not be equal pressures if it's a combi feeding the shower...?? They're both at whatever the mains pressure is. The hot might be slightly reduced through the plate I spose, but there's millions of mixers run off combis?
  13. M

    Mira mode mixer shower issue...maybe....

    no check valves on these...spoke to mira and they said they dont need em coz of the way the valve is designed...also its on a combi so equal pressures, give or take...
  14. M

    Mira mode mixer shower issue...maybe....

    Anyone had one o these (mira mode thermo mixer) getting crossflow from cold into the hot? Tia
  15. M

    Best Core Drill that can handle upto 6" cores

    the ddm 2 design is now (I think) made by 'sparky', or it's a fairly reasonable copy anyway....s'bloody heavy though. And I think a 150mm bit would actually spin you u around if it jammed....

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock