Thanks for letting me join. I've just set up as a sole trader so will more than likely be back for advice. In fact, where will i find advice on my probationary inspection?
Hi everybody, what's the best way of replacing this leaking & corroded yorkshire T under the floorboards ??
Along with many other things in this property it's been leaking for years probably never installed properly in the first place!
I am a little worried about using my small GAZ blowlamp...
I am urgently in need of a new boiler install in Huddersfield. My plan was to go with twin Opentherm boilers around 30KW each System is a very large listed home with currently a failed Potterton Eurocondense EC 65 KW, evoHome and pressurised water cylinder. Fan has died and is discontinued. If...
Hello
Quick intro....I’ve joined here because I’m planning a career change.... you guessed it, into plumbing. Im mid 30s and from a construction related background. Currently working in project management but sick of the corporate BS side of things. Wanted to trade train as a plumber when I...
Hi everyone I'm thinking about buying a powerflush machine and would really appreciate some hands on training by someone who does power flushing regularly. I'm 50 years old and gas safe registered .
Hi,
Im trying unsuccessfully to solder a 22mm to 3/4 yorkshire straight adapter. Ive done a fair bit of soldering before without issues but its all been on 15mm pipe.
With Yorkshire fittings im used to seeing a ring of older appear after about 15 seconds and then stop. However with this...
As in title, what's everyones favourite brand of end feed fittings? Mines are Yorkshire Endex as they have never let me down, and are thicker and much better made than the cheapo brands.
On the cheaper fittings, from the diy chains, not only is the copper thinner, but one end of the pipe goes...
I need to fit another rad and have spare outlets on the manifold. This manifold is now obsolete. Standard 8mm olives do not fit. I have found Legris brass compression olives at RS online which i would describe as a collared olive. Would these be suitable? Mytub.co.uk shows an illustration of the...
So I’m currently on a short holiday with family in Yorkshire in a caravan park. Being a saddo, first thing I check out is the boiler an Ariston - must say very impressed. It might be the brand of caravan, but usually have a Morco - enough to put me off combi’s for life. I usually stay in North...
Hi chaps
I've just bought a house that has an old single pipe heating system, but the boiler is a a modern WB Greenstar condensing boiler.
Boiler is staying as it's fine, but I want to remove all the old radiators (old and undersized in every room!), pipework etc and replace with new. It's a...
Hi
Seeking a G3 Qualified plumber.
Need my Ariston unvented water cylinder serviced, magnesium Anode rods looks at/replaced and also have a leaking tun dish.
Based in Keighley, BD20, West Yorkshire.
Thanks in advance
Hello everyone.
I am a level 2 adult student looking for tips and advice and employment to gain experience in the west yorkshire area. My course will be completed for June/July 2019 hopefully so I would be looking for a route on to gas safe once my level 2 is complete.
I dont have much...
Has anyone come across this? I've searched a lot and I can't find any instance of it. I'm redoing the plumbing in several rooms for different reasons and I've noticed that a previous plumber has used what appear to be solder ring fittings straight into 15mm compression fittings (no olive)...
Now I have been soldering fittings for a long time with a reasonable amount of success. However from time to time I still,have difficulties.
Should I use the very minimum amount of flux or should I add a generous amount ?
Should I heat up the fittings slowly or quickly ?
Should i put flux...
Hi, I've only really just began plumbing; have been working with another plumber and taking on jobs as I feel confident and able to do so! At this point, questions come up pretty regularly so am looking forward to any advice that may come my way! :)
hey all,
Looking for a qualified gas engineer to install a new unvented heating system that comprises:
2 x rm 300 indirect unvented cylinders or preferably ACV same size.
2 x vaillant system boilers giving a total of 60kw
Low loss header.
Suitable sized main heating pump
Mixing valve to give...
n141311
Thread
boiler
boilers
cylinders
engineer
gas
gas engineer
install
oil
unvented
wanted
yorkshire
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.