white

Drayton TRV4 White & Chrome TRV 15mm Angled & L/S | Thermostatic Radiator Valves | NoLinkingToThis

Hi all, I have just installed an outside tap and run it off of the supply from my kitchen cold tap water supply. I used a tee piece, isolator valve etc. I used boss white on all the joins. Working fine however the wife complained that the water tasted funky. Checked online and discovered it's...

Hi all, I have just installed an outside tap and run it off of the supply from my kitchen cold tap water supply. I used a tee piece, isolator valve etc. I used boss white on all the joins. Working fine however the wife complained that the water tasted funky. Checked online and discovered it's...

Hi, I've just had two Reina Colona radiators delivered and need to buy some valves for them. Sorry if this is a really obvious question but can anyone tell me what kind and which size I need? Or which ones to avoid. There are so many to choose from online that I'm sure I'll get the wrong ones...

bit of a feck up i bid and won a bulk load of fittings on ebay thinking i could collect last week but the seller had gone on holiday and they are now to far for me to collect im going to try to get them to send but if theres someone close to birmingham wants to collect i could contact them and...

It's been years since I have had to make some and I always use ready mix from the merchants. How do I do it again? Is it white sand and cement?

Hi lads, I have Riello RS 28 gas burner locking out at the white part of the disc at the very beginning of its cycle. You know the disc I'm on about where the different stages of the burners operation are so that you have an indication of what stage the burner broke down at. Anyway while...

Gentlemen, I need to move a kitchen sink including pipes and washing machine tap. I have cut the existing copper pipes at the first convenient place and temporarily put speedfit stop ends on. As I get a slight trickle of water I will probably connect to the pipe ends with compression or...

Hello all, I'm on the last bits (ish) with my bathroom install...!thanks to those for the help so far. A quick WC waste question: I'm using the original closed coupled toilet, but the position will be slightly different height and off the wall, due to tiling, etc. I'd like to keep the...

Is it best to use Boss White/jointing compound, PTFE, or 'nothing at all' , around the olives when installing compression fittings in both ‘potable water’ and ‘non-potable’ water situations ?

Family member has a floating WC, toilet seat has came off and can't get their hand round the back like you can on your standard pan to tighten up the bolts. Where can he buy a suitable seat? Had a look but can't find one, must be one out there as it's a pretty common set up.

gents, this is probably worth a punt. Does anybody know of a thermal store cylinder(150 litre) that has nt got the sprayed on insulation on show i.e the customer wants to look at a shiny white case. The only one I know of is the mega bucks elson aquanox. I would nt entertain a pullsar coil...

fixed a leak on one earlier. def not speedfit, never seen it before. was used as incoming main to a flat. was sealed to fitting with an olive and insert.

Which combi would people recommend . people say Worcester but why? Intergas sounds good and looks good..are they reliable tho? And what about vaillant?

does anyone know of any good brand, white bath tub enamel paint, that comes in a spray form? thanks

After some advice please. Just installed a new indirect vented copper cylinder and I've got a small weep from the cold water in Male iron 22mm x 1. I use plumbers tape wrapping the threads approximately 10 times. I've just ordered a 1inch fibre washer, will the washer help and should I apply a...

Hi I noticed yesterday water pouring out from a pipe from the top of our house its leaking water over the garden and its on and off occurring. I think its the overflow pipe since it appears connected to the water tank in my attic, so I made a trip up there and moved the top cover of the...

what are folks views on some of the flue showing - I know glowworm allow 600mm to potrude from wall and Worcester now allow theirs to be run externaly but baxi say non to be on show. gas safe don't approve of it

Hi chaps i hope someone can impart a bit of advice to me. Spent all all morning trying to fit a cast iron rad. All corners nicely sealed except one which has a very very slow drip. Have tried compounds, ptfes, lsx etc has anyone else got any ideas as it's driving me nuts. Thanks as ever matt

Allright guys i have a brand new mira advance in white and chrome brand new up for sale 9 kw £135 Posted in the UK i can post up pictures if requested