Would anyone know how to remove the two kitchen tap heads so that I can change the washers?
The taps are Grohe kitchen taps
There is no screw under the tap covers
There are no grub screws
I cannot pull the heads off of the tap using reasonable force.
Hi all,
i am wanting to install the above but want to drive x4 outlets and am unsire if this is possible.
i want to drive;
1. Overhead shower
2. overhead shower jets
3. handheld shower
4. bath filler
its item 4 i am unsure about as on the grohe concealed body, when showing 4 way control it...
just finished a refurb of a bathroom, has a grohe pneumatic concealed cistern installed around 13 years ago. Before refit water was leaking into bowl, after installation of complete new dual flush valve, water still leaking into bowl, air push button also replaced. Valve sits on a type of cage...
We have a Grohe Ladylux Pro Dual Spray pull down kitchen faucet, 32244
We like the look of it but on the default spray is a solid stream through the center that splashes up from the sink a lot. When you press the button to change spray the alternate spray is a bunch of thin streams around the...
Hi
I have a Grohe instant hot water tap that is dripping, and the spring safety handle burst. Bought a new cartridge and handle and got a plumber to fit them but a) the spring for the safety handle still doesn’t work (plumber swears he fitted it properly) and b) it’s still dripping after...
Hi,
We are redoing our ensuite bathroom and I am trying to find a shower. Does anyone have an opinion or experience with the:
Grohe Grohtherm Smartcontrol Perfect Shower Set With Rain Shower 310 Smartactive Cube?
I have been also looking at the:
Tavistock Index Thermostatic Concealed Dual...
I have a Grohe "Eurosmart Cosmopolitan" mixer tap which doesn't turn fully to the right (cold). I fear some sloppy installation and/or an (unwanted) hot water limiter incorrectly installed. Anyway, the guy who installed it is long gone so I'm on my own DIY now.
I took the grub screw out no...
I have a couple of concealed slimline cisterns.
They have started to leak water into WC, this is 100% not down the overflow pipe, as water level is well below that.
Took it out cleaned all … still the same (or worse if anything) …. From empty the infill ‘torbeck type’ starts filling, all is...
Hello,
I’m trying to fit a new Grohe tap. Flexi hoses are 15mm and don’t fit the 21mm (guessing it could be 22mm?) existing thread on the water feed valves. See pictures attached.
Is there an adapter I can buy?
Or do I need to replace the valve for a 15mm one? The copper pipework itself for...
How can i buy an exact replacement as i cannot see how to open the barrel to the hot ceramic disc to replace that?
Grohe
About 8 years old.
Thanks
Chris
I'm fitting a wall hung toilet using a Grohe frame and would appreciate advice on connecting the waste to the soil stack (to the right in the image). I am planning to connect the Grohe supplied waste (black pipe) to the stack using solvent weld pipes (don't trust the push fit not to leak) - the...
Hi, looking for some advice regarding my concealed Grohe cistern.
Problem 1 - There is a small amount of water appearing around the right hand side at the base of the tiling which houses the cistern and this has been happening for a few months but hasn't worsened. (I initially thought it was...
Hi All,
We recently purchased a Grohe sink and sink trap. However the Grohe pipe is smaller than the standard fitting. Have tried local plumbers merchants and supplier to get an adaptor but no one seems to be able to supply one.
looking for a 32mm - 34mm adaptor.
Any suggestions?
My WC is a Grohe adagio side entry concealed cistern.
This is operated by a push-button air bellows.
Recently water continued to spill into the pan after a flush.
The water level in the cistern shuts-off at the correct level.
I replaced the Grohe DAL discharge piston.
The problem remained...
Anyone fitted this pile of garbage all plastic ---t got to be the worst shower I have fitted and looks ugly as hell the performance is pony aswell grrr coustomers choice. Kop
Hi, if anyone can advise me on the following i would be grateful.
The images attached show the water inlet/isolation valve that comes with the grohe 3 in 1 toilet frame. The large connector appears to be 1/2" male and is tapered. the instructions are not clear what fitting this should connect...
Hi all
Struggling to find a new hose for this unusual union on a grohe deck mixer it almost looks like a outside tap hose lock, it’s not threaded at all, just a male spigot with an o-ring.
Thanks
I need to replace the washers on this old (1980s?) mixer tap.
Can anyone tell me how to release the knobs on these? It looks like a 4-way spring-action plastic clip and I can't feel anything like a screw in the bottom of it.
Many thanks.
A pals just rung me up , yesterday he bought a Grohe i-box for a up coming job for yours truly.
I have never fitted one but have heard they are a nightmare to fit but I am more worried that I have heard they are mainly intended for unventeds .
Anybody any experience with them ...
Thank you...
Hi everyone and thanks for having me as a member. I hope I'm in the right place, being an amateur!
We have a Grohe old-style Eau2 concealed toilet, about 11 years old, that has started running water after it has flushed. I assumed it was the seal at the bottom of the flush valve as that had...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.