Hi,
I need to install TRV on 3 rads in my flat. I'm looking at my Danfoss HIU (picture attached). I cannot workout how can I top up the pressure if I were to drain the system to install the TRV. I might need a filing loop for this.
Anyone familiar with this HIU?
Another question, would it be...
I want to fit a sussex flange to a standard hot water cylinder about 10 years old, normally there is a 1inch bsp tapping, this one has a male thread out of the top with a compression 28mm to 22 mm end feed reducer, held in place by a 28mm nut and olive, it does not have a male iron to copper...
Hi,
I am looking for a kitchen tap connector that would fit my tap (24mm male) to the dishwasher connector (3/4" BSP).
Cannot find it in the UK.
Any help/suggestions would be most appreciated
Kind regards
I need to hang a radiator (160cm wide, 50cm high, total weight around 35kg) via two brackets to a plasterboard wall.
The wall is external, so that it has studs (about 12mm deep and 50mm wide) behind the plasterboard and then bricks behind the studs.
I am lucky enough to have studs in...
Dear All
I am really confused but I have a foul brown smelling water coming from this bath in the material it’s self!! Sometimes loads of it I only installed it a month ago! Help!!
I have recently bought and installed a Roll Top Bath from Victorian Plum. It now appears I have water leaking from the bath material itself on the top edges. It is brown and smells foul. Any ideas?
I have recently replaced all fourteen Stelrad radiators eight singles four doubles and two chrome towel radiators on small bore 10 mm piping in my four bedroom detached house.The Grundfoss pump is ten years old and sounds good .no bearing rumble.The Ideal classic ff 350 boiler is twenty years...
Hi all, I have a Megaflo Heatrae Sadia running from a conventionla boiler. The boiler is 12 months old, the cylinder about 6 years old.
The cylinder has two separate pipes in at the bottom left, both of which are too hot to hold for more than a second. There is a stone cold pipe going in the...
Hi All,
I have a GrundFos Home Booster, the 3.5bar version which has transformed my flat, its used for every tap aside from the kitchen cold tap and the kitchen white goods that need mains, it also supplies the pressure for my combi boiler that is the hot water and central heating system.
I...
Hello ,trying to change stop tap it come up from floor in garage ,The tap is stuck in the blue MDPE PIPE.. its compression fitting , the nuts have been undone and the top pipe is out the way ,however the tap is stuck in the blue pipe. Do I just give it a bit more of a pull?
I am needing to bleed the radiators at the church building and I opened up the boiler cupboard to see if there are any cock valves to refill the system, but can't locate any. I haven't been able to locate a pressure gauge either and it appears that this boiler doe not have a loft tank either...
Hi all. I hope you’re well!
I’m having issues with my Flomasta toilet in my main bathroom. This was only installed a couple of years ago after moving in where limescale wreaked havoc with the previous system.
as you can see from the video, it’s filling from the top (the video shows this much...
We have introduced a range of top heating spares from select manufacturers , Take a look here
Heating Spares - CorgiDirect - https://www.corgi-direct.com/heating-spares-17866-0000
Hi All
DIY homeowner here..
I replaced the thermostatic cartridge in my shower today, but after I finished and re-opened the water mains, water started leaking out of those 2 small golden screws at the top and bottom of the cartridge (picture attached).
Could anyone please kindly help me...
Hi, I have a Tre Mercati Bridge Sink Mixer Tap. The taps are screw down. The cold water tap leaks from the top when turned on (the water wells up around the top). When off it then still tends to leak a little. I've taken it apart but the O rings all appear to be OK. I've taken some photos and...
Hi, here is a photo of the valves. Which ones do I need to open in order to top up the boiler please? I presume it’s the ones connected to the braided hose. But why does it have 2 taps on each end?
thanks
Hi, We recently had a Worcester compact system boiler repaired under warranty where the fan had failed. Since this has happened, the top floor radiator has needed bleeding constantly and additional water added to the heating loop. There's no apparent leak. I'm guessing the boiler is releasing...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.