Hi, I have a Halstead Ace boiler and just a few days ago, I went to repressurise it as the pressure dial was on zero and we had not hot water or heating. Anyway, when I used to repressurise before, I would hear the water going through and I was hear the pressure up. Now, I don't even get any...
Alexander7
Thread
ace
filling
halstead
heating
pressure
problem
repressurise
sounds
water
Hi all, when you fill a system its to my little knowledge, that you start downstairs rads first.
So is it best to close one side of each rad seperately, anyside if you don,t no which is the flow and return?
Then bleed the rad and then open the chosen valve, then move to the next one and do the...
Hi
My boiler (vaillant ecotec pro 28) is giving f22 message. The manual (and this forum) tells me that it needs to be refilled but I'm struggling to see how to do it. The boiler is up in the loft and there is a flexible piece of tubing next to the boiler but it's not obvious to me how to...
robboplumber
Thread
black
connect
ecotec
filling
pro
pro 28
vaillant
valve
ecoTEC pro28. I've found the braided loop but it's not attached at one end. I'm guessing it goes to one of the two grey valves, but don't know which. Any clues please?
Hello AllI manage 6 apartments in the same building and recent repairs to the plumbing and boilers and subsequent replacement of a boiler I noticed that these were becoming a lot more frequent and Following my inspection of the apartments I seen that the filling loop was still connected to...
Hi all,
called to look at a Vokera compact Se (2005)where there was water constantly filling from the domestic hot water over pressurising the boiler. Checked expansion vessel and ok. I can't see any divertor valve, so am I right in thinking that there is a leak in the heat exchanger between the...
Hi all,
I'm new to the forums and relatively new to plumbing, and wondered if any of you experienced chaps could help me out...
I went to a job today, where they had urinals that were constantly running out of the flush pipe and wasting water. The cistern fill pipe was fitted with an...
Hi everyone
Im draining down an unvented stystem on the first floor, but I can't see the filling loop anywhere, or where one would attach. Surely it needs to be pressurised to 1.4bar, but how???
Hi all. Is it a common problem with the internal filling link key to get stuck. We only fit worcester at work and I can picture the actual link but can't picture what the key goes into?? Any help
Hi all. Thanks for looking. I have 2 questions
1 how to fill old flue hole that does not conform to regs. Problem is its 3 floors up. Can't be reached from window. How to fill from inside!!?? If even poss.
2 gas line has to go past electric maim isolation switch before consumer unit. Only...
is it ok or even a good idea to use softened water in a central heating system? this is partially related to another post. the heat exchanger is iron, but it feeds via an indirect coil an RM stelflow unvented. will using softened water cause corrosion?
Hi Guys,
I'm experiencing a bit of an issue here:
When turning the taps on for hot water, there isn't any current / flow of water coming in and I don't know why.
It felt as if something / someone turned the tap off.
As a result, this has effected the kitchen, washing machine, dish washer...
hasa
Thread
below
different
dripping
filling
heating
loft
please
recently
slow
tank
water
water tank
Need help please. I removed a radiator yesterday as I was decorating, watched a YouTube video on how to do it. All went well no leaks, did the wallpapering and put it back on. I switched on the heating to test and bled the radiator as the heating was on. Radiator filled up and no leaks. Really...
Mattf
Thread
bar
boiler
central heating system
combined
filling
oil
radiator
reading
removed
youtube
I have got a problem with only 1 Radiator. It keeps filling up with Air and needs to be bleed. Its the radiator which is nearest to the airing cupboard. In the airing cupboard there is 2 2 port valves, pump and By pass Valve and Cylinder. Anyone got any idea's what could be causing the problem...
SWE
Thread
air
corrosion
cupboard
filling
hydrogen
keeps
problem
radiator
which
Hi. Can someone please tell me how to take an Ideal Standard filller/float mechanism apart please? The filler keeps lightly leaking from the top (by the arm) and also leaks into pan constantly.
The arm/float and filler is all one mechanism with the siphon to the right of it. (I would post a...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.