hi from Croatia
One crazy plumber make many 90° piping for toilets drainage. I need to correct because i am suspicious that this setup can work, especially F1/90T.
One toilet is on second floor and must have 180 bend to vertical pipe. Now we have 1m 110mm pipe from toilet into 90° left, than 1m...
Hi All,
I’m installing an ufh system using procrate and 16mm ufh pipe. The procrate is laid on top of insulation but I’m finding that at each bend and return the pipe is either pulling out of the procrate or the procrate is lifing up. What am I doing wrong? This is the 3rd system I’ve installed...
TL/DR: Can I have a bend of 90 degrees in the dry section of a 4-inch soil vent?
Hi. I am renovating a small bathroom. There is an awkward part of the wall where the builders boxed off a large section just to conceal the 4-inch soil vent. I realise, of course, that the soil vent is essential to...
Hi,
We’re currently fitting a slimline shower waste. Due to a tight space we’ve had to put in a few (4) 90 degree bends from the shower trap to the waste exiting outside.
It’s essentially resembling a ‘d’ shape. The top of the ‘d’ being the waste pipe exiting the wall.
Does anyone see any...
I wish to install a macerator for a ground floor toilet.
I need to go out through the wall and around an external corner.
Is something like this suitable Grey 32mm Solvent 90 Degree Swept Bend ? With maybe a swept tee such as this White 32mm Solvent 90 Degree Tee when it exits the wall?
If...
Hello, I'm looking for some advice on how to tackle this... We have a slow draining sink in our utility room. When the washing machine pumps out water, it comes up into the sink before slowly draining away. I think some of the water may drain back to the washing machine. This has been a problem...
I have two 0.5m long extensions and two pairs of 45 degree bends. Internal 110mm and external 160mm diameter. Offers invited. Located in North East Hampshire j4a off M3.
Hi, I'm installing a bathroom at the front of the house and need to get the main 110mm waste pipe to the back of the house where the main stack is.
I've had to drill a large hole in the landing wall in order to get the pipe through to the other side, however directly on the other side of the...
Hey guys,
just wondering, can you bend 22mm 90's up into the valves or is there not enough pipe left? I know you can with 15 but I've always used elbows, I've never tried it and I'm not sure when I'll get the chance to give it a a go
Thanks
ApprenticeTom
Thread
bends
boiler
combi
combi boiler
elbows
oil
question
street
vaillant
Hey guys, just need some advice..
When doing an offset bend, how do you get the actual offset measurement? I know how to do an offset by eye but I want to be more accurate.
for example if you have two clips spaced apart, would you measure the difference from centre to centre?
thanks!
Hi all,
I need some advice installing a new toilet. Please tell me if you think if it is likely to create blockage if I install an horizontal rigid pan connector with multiple bends; it is about 1.5 meters long from the toilet to the vertical pipe, and I have limited gradient (maybe 15mm if I...
adamlondon
Thread
behind
bends
connector
horizontal
multiple
oil
pan
pan connector
soil
through
toilet
Hey has any one used the texhnique of running 10mm microbore copper pipes behind the skirting board and sweeping out to radiator valve. Like the picture below. Guessing you use an external spring to bend the pipe?
Hi guys,
was as just interested to know what pipe bends do you find you use most on site?
I only ask ask as I been practicing my 90 degree, offset and crossover at home before I start my apprenticeship next week and having lots of fun doing then and have to say getting quite good.
someone...
is anyone experienced with hep20 plastic 22x10mm 4port manifolds.they differ from the other fittings (bends ts etc)slightly, are the10mm ports demountable.ive tried and had no joy.help!
gasso
Thread
bends
fittings
help
help needed
hep20
manifolds
needed
remove
I live 3 storeys up in renovated buildings. Two plumbers have been unable to locate the blockage to my kitchen waste pipe. They've tried plunging but to no available. The pipe bends three times at right angles so snaking won't work and they can't see where the pipe goes. There are no neighbours...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.