zone

I have a Heatmiser UH8-RF controlling my underfloor heating, connected to the NeoHub with three zones with NeoStat v1 thermostats. This is about 3 years old now and when setup everything was installed worked fine. All the main current functions work - I can control the UFH with the app and it...

We currently have the ground floor wet UFH and upstairs rads running from an unvented condensing boiler. Any advice/experience on the following please:- The 1st-floor and 2nd-floor landing will retain radiators but they will be added to the underfloor manifold as a single zone as it will...

Hey folks! I have been trying to get my heating up and running properly but I have had some trouble. I bought a new house this year and I have only just got to the point where I'd like to use the heating a bit. The house has two honeywell thermostats (Picture attached) one upstairs one...

Hi all, I have a 28mm zone valve for a C Plan I want to fit and would appreciate some advice please. I’m looking for the best way to adjust the existing pipework - my idea is to fit the valve at the green circle, tee off beneath it for the vent pipe and cap off the reducer at the cylinder...

Hope someone can help. I have dual zone heating in my new build. I have a TPOne-M downstairs and a TPOne-B in the master bedroom upstairs. When I turn on the heating using the downstairs TPOne-M it heats up half of the ground floor, kitchen/diner, hallway and then 2 of the bedrooms upstairs...

So I have a combi boiler with a hive hooked up to it and from what I can tell its a Y plan(I think) with 1 zone. So I crank up the heat on the hive it makes a call for heat and boom the boiler fires up. Downstairs I want to install an UFH wet system which doesn't look like too big a deal...

Can a three port zone valve allow circulation through both rad circuit and cylinder coil at same time or does one circuit take priority??

Hoping someone knows a wiring centre that fits this requirement. I have 1 UFH zone (3 circuits) and 2 Radiator zones. Was looking at the Heatmiser UH4 wiring centre schematic, it shows that I can only use zone-4 for a single radiator zone. By selecting the dip switch to not engage the UFH...

Hi, Seems like both my upstairs and downstairs HPA2 zone valves are on the blink. Every other day one of them doesn't switch off at the thermostat cut off temp and I come home to the Bahamas 😅. Firstly, is it worth trying to repair them or is the fix only likely to last a short time before...

I have a new build and has 2 separate zones. One thermostat in main bedroom, one in living room. Main bedroom thermostat controls all bedrooms and bathrooms, living room thermostat controls all downstairs and the upstairs landing. Rooms with thermostats have no TRVs as expected, and all other...

I have a new build and has 2 separate zones. One thermostat in main bedroom, one in living room. Main bedroom thermostat controls all bedrooms and bathrooms, living room thermostat controls all downstairs and the upstairs landing. Rooms with thermostats have no TRVs as expected, and all other...

I can't see why this wouldn't work but thought best to ask encase anyone has tried it before or is using it and would care to comment. So the plan is to install wet UFH in a soon to be built kitchen extension. The ufh will be installed in the whole kitchen area which will be of block and beam...

Hi, I'd appreciate a bit of advice about my hot water and heating system.. So, we moved into a new build about 5 months ago and we have a TheraQ ProLite SS 250 unvented tank, we also have a gas boiler and Hive multizone. My understanding is that the boiler sends hot water to the tank to heat up...

Hi all, For my boiler worcester bosch greenstar 30Kw Ri Compact, I noticed that, within programmer set time, for heating, if the house temperature has reached set temperature say19°C, the zone valve for heating will close, the boiler's a burner light (green) will be off, and blue light is off...

Hi, I am in the process of setting up underfloor heating in my home. I have used polypipe overlay plus underlays and 12 mm polypipe pipe for running hot water as advised by my builder. Due to this I now have to get a polypipe manifold as there are no other fittings which would allow me to...

Hello. I have a two-zone heating set up, with each zone controlled by a 2-port zone valve (Honeywell V4043H by the looks of it), and each zone has a two-wire HoneywellCM707. I would like to replace the CM707 in the master bedroom (for a mechanical stat that doesn;t click). In terms of...

Objective: I have an existing s-plan plus (see below for details) heating and hot water system, with 2 independent heating zones. There is a separate programmer and a simple room thermostat for zone 1 and programmable thermostat for zone 2. I have purchased the Drayton Wiser 3 zone kit and...

Would anyone know if I could use 2 hives with out a hub and buy a separate hub for a house with 2 heating zones? I quoted just before Christmas and the hive were £135 each but now they are £160 2 without a hub are £100 each and a separate hub is £80

Hi everyone, I 'think' I've found a cheap solution to fulfilling all of my family's heat automation needs using Terrier i30 TRVs (eTRVs that have a timer, but no way of calling the boiler for heat). However, it seems too good to be true. Therefore, I wondered if I could run it by some of you...

Hi all, Does anyone know if you can replacement heads for this zone valve? And if so, can you replace the head only (without having to drain the heating pipes)? Thanks Jennie