Hi Guys and Gals
I have an old toilet that needs removing to retile, the only thing is the toilet appears a tad odd.
It wastes out of the bottom then out to the soil pipe, I havent a clue what sort of toliet it is but I am concerned that when I remove it I may break something and parts may...
Jon H
Thread
armitage
connect
depends
floor
old
something
style
Im assuming it just needs a cold water feed
but what fitting shall i leave on the end for the customer who hasnt bought the fridge yet?
its a
Read our user reviews for the Samsung RSG5
thanks in advance
ashtonjay
Thread
american
fridge
plumbing
pumbing
reviews
style
valve
Been in the game for a little while and am about to fit my first old style cast iron rad on Monday (you know the proper old hospital hallway style). Can you still use TRVs with these effectively? Would appreciate some advice. Thank you
Hello All
Sorry to bother you mate but after much reading I came up with the following heating controls schematic. However a couple of items remain unclear.
1- how to wiring up this particular room stat
2- Confirmation on how to wire up the boiler dedicated pump earth , live and neutral...
Hi, brand new to the forum. This is literally my first week in business being self employed and this is my very first job! Could have been easier haha!
Spoke to the customer on the phone, going to look at the job tomorrow.
Current setup: Gas fired Aga stove doing h/w & c/h (16 rads & 2 zones...
JJone
Thread
aga
boiler
gas
help
oil
stove
style
system
system boiler
I have an Eastwood range cooker, we purchased on e-bay, I wish to install it in my renovated kitchen, in runs on mains gas, and I understand from the experts it needs to feed 2-3 radiators and a hot water cylinder. I need a gas safe plumber who likes a bit of a challenge, whilst I'm prepared to...
I have an "old style" radiator in my hall - it has no "fins" on the back. I reckon its about 20 or 30 years old. Its double panel and measures 127cm by 60cm approx - does anyone know roughly what its heat output might be please ?
thanks
quick question...never encountered this problem
putting a towel rail in bathroom but thermal store with combi expansion is on same floor, how high can i go with the towel rail? to as high as the water level in the f&e or lower?
cheers
bob
bob the plumber
Thread
below
cheers
level
lower
rail
style
system
towel
towel rail
vented
water
Hello all
I've got to replace a leaking HWC
I'm fine about doing the job exept where you would normally find a burned out knackered electrical immersion heater there is an essembly that I've not come across before.
View larger image here: 1938 cylinder | Flickr - Photo Sharing!
It is...
There is a lot of discussion about this make of grips or that and generally good grips are quite expensive.
I found these tonight. What seems like a set of alligators without the dipped handles which if they are they are the cheapest i have ever seen.I bought 2 pairs.
When i get them in i'll do...
London's burning: Gas lamp engineer keeps the city's historic centre illuminated in classic Victorian style
http://www.dailymail.co.uk/news/article-2056431/Londons-burning-gas-lamp-engineer-keeps-citys-historic-centre-illuminated-true-Victorian-style.html?ITO=1490
:drunk:
Puddle
Thread
centre
gas
going
lighting
still
strong
style
victorian
Hi,
I have recently been to a customers property who has been having a problem with a leak from a flush pipe. The customer had removed the rubber cone himslef and thrwon that away and fetched a new one but the new one does not fit as the hole is larger than the pipe. I have been to the...
CRAP CRAP AND MORE CRAP the misiss's waters have broken eeerrrrrmmmmm eeeeeerrrrrmmmmm HELP
stiched me right up all I want is to go to bed and
iv got a 3 & half year old alsleep in bed that needs looking after now i need to bee In
two places at once HELP
im happy thats she is on her...
Hi All, First post on the forum and hope its a good'n !
Story goes like this....
I salavaged a number of Ideal standard 4 column cast iron rads from a warehouse a few years ago, brought them home, removed all the old fittings, flushed em out with a hose in the back yard till water ran clear...
RonG
Thread
bar
bottom
cast iron
central heating system
cold
cold radiator
connect
cool
ecomax
efficiency
flow
hose
hot
hot rads
hot water
ideal
iron
kitchen
lukewarm
old
pipe
pipework
piping
problem
radiator
style
system
trv
valve
valves
water
wide
I recently purchased a butler style ceramic double sink, however I am having a nightmare trying to find waste outlet fittings to fit the two large outlet holes, (both of which have `INBUILT' overflow). I have measured holes and they are 3 1/2" (90mm) with extended flange measuring to 4 1/2"...
hi,
1) anyone know what manufacture do a 300 x 700 panel radiator in chrome?
(not really designer flashy one :) )
has anyone ever had a paint job on one to look chrome?
2)
also i am looking for a 2 channel timer/programmer colour of chrome or metal style ?
if you know of one where can i...
heatman
Thread
chrome
job
metal
paint
panel
programmer
radiator
radiators
style
timer
trade
web
where
I've just fitted a new PCB to a 24i. The hot water is coming on fine but not the heating.
I do not have a room thermostat rather a mechanical timer. When the programmer is set to constant and the temperature dial is rotated off the off mark, the heating burners do not kick in - the fan runs...
MrB
Thread
24i
boiler
bosch
central heating system
combi
combi boiler
digital
flame
gas
hot
hot water
parts
pcb
plumber
problem
pump
style
temperature
timer
water
worcester
worcester bosch
work
Hello all
Can anybody please help me find (purchase rent or borrow) an old style main stopcock key that is 1 1/4 inch square drive? I got yorkshire water (i'm in Holmfirth) to turn it on a few weeks ago, Its a quarter turn (clockwise) "on" then another quarter turn in the same direction to...
Wortonmiller
Thread
bar
bits
burst
flat
free
high
hot
job
mains
merchant
merchants
needed
old
pipe
pipes
plumbers
style
supply
test
valve
valves
water
work
Hi, could do with some advise on which basin wrench, Im not a plumber but do alot of stuf at home and also others.. anyway im looking to buy a basin wrench whats the best, the more traditional Crows foot? or the newer Adjustable/ changable jaw type? also whats the most common size? 1/2 -3/4inch...
rabu
Thread
basin
bath
plumber
plumbers
size
style
taps
traps
web
wrench
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.