power

I have a customer that wants a mixer shower replacing with a power shower, the only problem is the pipework is teed off of the basin above floor and run to the shower over the bath. She says that she used to have a power shower there before but was just wondering whether you guys think this...

I understand that it's not advisable to power flush back boilers. What other boilers would people recommend not flushing. I am kind of after a bit of a list what not to flush if I bypass every boiler then I could just crack on with fx2 and neutraliser??

Has anyone joined this mob? Are they any good? The logo would be good to use on the van and cards I am sure. I am also looking at there training day

Just gone through my power tool kit today got quite a bit 1x 12v dewalt drill 1x 18v dewalt drill ( on last legs) 1 x 240v cheap drill 1x 110v makita ripsaw 1x 110v makita drill 1x 240v makita drill 1x 24v makita drill 1x 18v makita drill 1x rems amigo 1x 18 v milwaukee 1x milwakee impact...

Hi all, I have a triton power shower. When switched on with the temp set to hot, the pump runs dry, if I reduce the temp, cold water will flow. Increase the temp and it will run dry for a minute or so, eventually hot water will flow. If the shower is used regularly it's fine, but if not used for...

Gunna open a bit of a can of worms hear, do u or do u not flush the boilers? Combi, conventional, back? Reasons as to y u don't if u don't please. I am relatively new to flushing and I am getting a lot of conflicting answers. Also I have been cracking on with fx2 and a neutraliser with good...

Hi guys, I have been asked to go and have a look at a Triton power shower in the morning. I don't know the model, if it's tank fed etc. What things should I be looking for or have in mind to check before I get there? Pump needed? Flange needed? Blockage/restriction somewhere. Anything...

Where do most of you buy your power tool gear?

Hi, im looking at the cost of buying my own power flushing unit, there so pricey. At a £1000 I don't want to be disappointed. What should I be looking for. Thanks in advance.

Hi me and my partner have just moved into a new house and the boiler was working fine last night on our first night however I have woken up this morning to the unit being completely off not even showing the stand by display or the blue light, I have adjusted the thermostat and turned the unit...

Right iv got my tight sod cap on. I bought the fernox powerflushing machine last summer, used it a few times been succesful. Nervous on first use but after that you get used to it. Iv been looking at the filters, £500+, how successful do you think a thin gauze with a strong magnet would be...

hi all had a short on my lighting circuit at home and now my programmer is not working or showing any display any ideas.Don t understand why as it should not coming off the lighting circuit.

Is soooooooo boring, someone talk to me!

Hi, someone has installed nest and wanted the heating controls to be separate from the hot water (water heated up separately) I've had a little read and it seems to be a system boiler with a cylinder built in which would not make it possible. just want clarification. thanks

Hey guys, Fitted a new Salus pump (mp100a i think it was) to a Pulsa coil 3 its worked since Saturday and got a call today the tenant had no hot water. When i got there i noticed the digital display on the side had no power so i changed the fuse in the spur and was still having the same...

I have a pumped power shower running of a indirect cylinder the shower head is just below the header tank but the pump wont turn on unless the head is on the floor or I shake it about can I put a accuimilator tank on or any suggestions to what will sort it out all help will be apprecitated

I have a pumped power shower from a indirect cylinder but the shower head is as low as I can have it and the header tank is just above it. the pump wont turn on unless I leave the head on the floor or shake it can I put a small accumulator tank on or any suggestions

I am trying to do a power flush at a friends house. The bottom union on the pump is impossible to access, can I remove the 3 way valve and connect there after disconnecting the power to the pump? There is nowhere convenient to connect in to the pipework elsewhere. I know you can use pump head...