mixing valve

Hi guys, quick question regarding tmv's, I have been asked to install a tmv for a school as the childrens sinks are very hot. They have 5 sinks in a row, would I need a separate valve for each sink or could I use 1 for all of them? Thanks

Doing some alterations t a house with a wood chip boiler that feeds a large buffer tank, this has a coil for hot water that is then circulated round the property. the hot water is very hot (70*c) can I fit a mixing valve at the cylinder between the cold supply and hot take off . if so can...

Hi all had some new horne 15 tmvs fitted which were set and left on 41 c but for some reason the temperature will not hold within +/- 1c. The temperature always raises up to 43-44~ after adjusting back to 41 with allen key. I have adjusted the tmv back to 41 for a few days in a row and the...

Hi, can anyone recommend a good mixing valve for underfloor heating with a good temp range. My UHF is connected to an accumulator tank and water temp could be anything from 30-85+ degrees. I've a Robot Compact Manifold and I don't think it gives me the variation I would like. regards Archmoco

Can anyone tell me how to take the cover off one of these so I can adjust the temperature slightly? Nuastyle S7435aa Thermo Mixer Valve Cp I've tried pulling it to no avail... thanks!

Hello, the Thermostatic Mixing Valve on my thermal store has gone. I would like to do a direct replacement if possible. Does anyone know who may stock a Taconova 22mm 30-70 degree C TMV in the UK. I live in York if that helps. Thanks.

I have recently installed a TMV in my bathroom and it has been very tempramental with the Hot water. If i turn the temp down then cold comes through no problem. if i turn it up to provide controlled ho****er then tap stops. If i'm lucky then i will get nice hot water. so i know the thermo bit...

Got a 30 of these if anyone is interested, will sell separate or how many you are wanting. They are all brand new still boxed. I am in glasgow would prefer collection but could arrange delivery at extra cost. Offers welcome

Morning one and all.. Trying to ID replacement valve. 1 &1/2" BSP, believed to be mixing valve as opposed to diverting, from pool h/ex..... No luck with normal suppliers, any nods in the right direction greatly appreciated!

Apologies if this has been asked before, I did have a search but couldn't find anything. I am living in France and fitting an oil fired boiler for central heating only, ie not water heating. It is pressured off the mains ( so expansion tank and relief valve fitted, not a header tank)...

I am moving my bathroom into another room in the house and installing a thermostatic mixing shower above my bath, i will be connecting the shower upto the hot and cold pipework for the bath taps, Do i connect the hot for the shower before the TMV for the hot tap or after

High temperature solar mixing valve by Inta. Solar kit came with a new valve so not needed. Cost about ninety quid. Do it for £40 inlcuding postage.

Hi Gang Building regs in Scotland dictate a TMV must be installed, the DHW will be heated by gravity solid fuel stove/immersion heater, with a head of 2.8 metres. I need a low pressure TMV with a good flow rate for bath filling.. Can anyone recommend a good make/model? Thanks.

hello i have been asked to quote for servicing 8 thermostatic mixing valves. i've never done this before. what do i need to do to service the valve. there is 6 under basins and 2 under baths...... thanks...rob

Hi Gang What are the best TMV models for a soild fuel indirect heated gravity flow hot water system? Thanks. (edit: sorry it looks like this should have gone in the Taps and Valves forum)

Hello: I am sure that my question will seem quite trivial to the members of this forum, but not for me. For, you see, I am an Electronic and Computer Engineer by trade and I was always taught to keep my hands out of water!:) Here's my problem (this description of my system is the best I can...