HI, we have replaced 3 manifolds (1 upstairs 2 downstairs) with new Warmup units. The installation manual from Warmup states that to fill the system you have to fill each circuit in turn using the fill / drain points on each manifold. However, my plumber said that he always uses the filling loop...
Hi,
Have a couple of old microbore 28mm to 10mm manifolds for the central heating. Not sure of the condition on the inside of them but outside there's a fair bit of corrosion at the solder/compression joints. There not leaking so was wondering if they can be cleaned or if it's better to...
As part of deep house renovation, planning to install wet ufh on the ground floor, and radiators on upper floor.
Two bathrooms will have both water based towel warmers and electric ufh, and need dual thermostat to separately control air temp (by running towel warmer) and floor temp.
Need...
I am doing heavy house renovation and want to have ufh (multizone) at the ground floor and radiators on upper floors.
I want to have consistent controls, with manifolds feeding both the ufh loops and radiators, and the same type thermostats controlling both (depending on the room, the...
I'm sold on the idea of sanitary manifolds. I'm an avid and capable DIYer but finding the information out there on domestic manifolds systems lacking to say the least.
Here's a diagram for my proposed approach to converting my house over from your usual 15mm pipe with T junctions everywhere...
I wonder if anyone can help me. My house has under floor heating but after having a new boiler fitted it doesn't seem to working as it should do. I wanted to get the system balanced but some of the flow meters are stuck and not all of the actuator/flow valves seem to be moving as they should. I...
Had a contractor come out today for in-floor heat not working. I have 2 zones each with Rehau manifolds supplied from a single pump and neither zone worked. Contractor felt the pump had failed and replaced it only to discover that the system still did not work. After much consideration...
Hi
I installed ufh on two floors. My question is can I run two manifolds on two floors with one pump and mixing shunt?
How do I go about connecting the manifolds together, do I run a T straight after the pump before it enters the first manifold or do I connect the second manifold after it...
Hi guys, need help in identifying a manifold if possible, if not could you point me in the right direction to the closest thing available, pipeworks all 8mm and its quite tight so dont want to spend forever repiping it all, no markings on the manifold at all.
Thanks in advance
Looking for competent plumbers to price and work with the design of water/gas/waste plumbing for a terrace of 3 houses in Surrey.
UFH manifolds and pipework will be installed by others - feeds to manifolds part of the job though.
3 kitchens
3 cloakrooms
8 bathrooms
3 utilities
Gas central...
Hi
does anyone know if the two makes are interchangeable?
im keen to go with mysons stats etc but need to know whether I have to use their actuators for ufh manifold
thanks
Cubbs
Thread
actuator
actuators
centre
heatmiser
manifolds
myson
wiring
Hi, we moved into a house with a 3 years old underfloor system. I notice a small leak coming from the pin (sitting in manifold under actuator). I think the leak stops once the actuator is removed and taken off the pin. I suppose I will need a new pin unit but as a similar leak seem to be...
BenH
Thread
actuator
leaks
manifold
manifolds
under
uponor
valve
years
Hi,
Some of my radiators are not getting hot at all or some are just hot at the top and from one side.
System Description.
- Downstairs mostly Wet Under Floor Heating. 14 Flow Circuits, with 8 Room Stats / Zones - WORKING OK
1 Towel Rad fed from upstairs
- Upstairs - Radiator based, single...
Hi,
I am slowly refurbishing my mothers old house for us to move in.
Fitting a new CH system. (All gas work and boiler installation is being done by a local firm).
The problem I have is with the CH manifold. Where I am joining the manifolds together they leak, a small drip now and then. I...
Hello,
I am renovating my 3 bedroom house and currently dealing with central heating. I got a plumbing 'expert' who designed a central heating for the house:
It is all on hep2o with 22mm manifolds. From there 10mm pipes goes to every room. It looks like this...
gregd72002
Thread
central
central heating
design
heating
house
images
manifolds
is anyone experienced with hep20 plastic 22x10mm 4port manifolds.they differ from the other fittings (bends ts etc)slightly, are the10mm ports demountable.ive tried and had no joy.help!
gasso
Thread
bends
fittings
help
help needed
hep20
manifolds
needed
remove
Why is it every plumber you speak to gives you a different view of what the best way of doing something is?
First there was the argument about copper v plastic. Now its 15mm or 10mm plastic.
So I had a guy in today to quote on a new boiler. He was really good and suggested I go for 10mm pipe...
Im doing a job where we have installed manifold soil fittings at the base of a some soil stacks at floor level. This is so we can easily discharge the shower wastes into it (there are 5 showers). The link below is the sort of thing that has been fitted.
Waste Manifold Black SP588 | Black Pipe...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.