high

Hi all, I’ve a customer with a failed double check valve on a water softener, it’s 22mm compression but with a far larger bore than the usual DCV’s you see online. Anyone know if they are called something different or where I can get one? I’ve even been on the water softener website and they...

HI all, finished fitting the above boiler yesterday. Straight swap, side access flue with only the elbow off the boiler. Gas pressure 21mbars on full chaff. (right by the supply) when doing the co checked, minimum was as expected- 3ppm, .0.0000, and about 7,8% Max on the other hand was 240ppm...

I was wondering if anyone can help with this. On servicing a two year old Vokera Unica i28 I carried out combustion analysis checks. The high readings were fine but when I checked on low I was only getting 6% CO2. When I slowly started to adjust the valve I couldn’t get the Co2 anywhere near...

Hi, Grohe shower Grotherm 1000 smart starts very high temp, then runs cold (28C) in 2 mins Changed thermostatic cartridge for a new one Exactly the same problem? Inlet temp 54 C Inlet pressure Hot 3.5 Bar Inlet pressure Cold 3.5 Bar Any advice appreciated Jason

Hi folks. I've noticed recently that water is dripping from my Megaflow overflow pipe outside coinciding with the time the heating turns on to heat the water. Whilst the water is dripping, the pressure on the Megaflow is reading around 8 bar. Dripping from overflow stops and the pressure...

Hi all. I need to improvise a flush pipe some how. Anyone managed to do this with waste pipe at all. Basically the cistern is on the back of a 2 inch stud wall of where the toilet will go. The pipe cannot go straight down due to a washing machine needing to fit into the space below the...

We live in a high rise on the 18th floor. I want to have a under the sink water filter installed. Waterdrop 10UA Under Sink Water Filter System, NSF/ANSI 42 Certified, Under Counter Water Filter Direct Connect to Kitchen Faucet, 8K Gallons High Chlorine Reduction Capacity, USA Tech...

I am looking for suggestions /advice on getting a commercial high pressure toilets that does the job in one flush. Does anyone have any toilets they can recommend?

Hello, I’m trying to replace an antique high level cistern with a more modern ceramic one. The flush pipe is routed in a very specific way so the new one will probably need to be bespoke. Does anyone have any experience, or at least seen, bespoke flush pipes? I was hoping they could be made...

Good evening - I wonder if anyone can shed some light on this. Squealing high pitch TRV's when reaching the required shut-off temp. I understand its probably the pressure in the system making the pin in the TRV vibrate. Or pump turned up too high - which I guess would cause the same effect of...

Hello, Getting some work done in my downstairs WC and my installer and given me a list of products to buy with some recommendations. We are replacing the exposed cistern toilet with a hidden one. It will be a back to wall, floor standing pan with a shelf above it to put stuff on. I've been...

Hi, Trying to decide which cylinder to go for? I am renovating my house which will end up having four bathrooms and a wc. I am planning to go for a 300l unvented indirect cylinder as currently I have a vented cylinder with a cold water tank in the loft and face issues with hot water pressure...

I am having to work on a concealed shower but there is no service valve and so I am having to isolate from a large mixing valve which is linked to several other showers. I am going to add a service valve to make it easier for future maintenance but the pipe connected to the shower is 15mm...

hi all some advice combi boiler is heating water and heating comes on fine. its an ecotec plus - vaillant Issue - Pressure is way to high, sits at 3.3 and goes right up to 3.7 when on. im worried something bad will happen soon. im not sure when it started, but been like this for a month or...

Hi, can anyone help me resolve this issue with my ideal logic combi Esp1 35. It is making a very loud high pitched noise whenever the outside temperature is cold, when either CH or HW is being used. For example, first thing in the morning on a cold day, run hot tap or turn up CH stat and the...

Evening all, I’m hoping somebody can help. I have a wet speed fit UFH system, that controls 9 loops on the ground floor, each with a separate zone thermostat, flow valve and actuator. The problem I’m having is when the main programmer (which controls the entire system), is left on (I.e...

Hi Guys, Hopefully someone can help me out - the pressure reading on my boiler and in the hot press seems too high. Just wondering how can this be adjusted? Hot Press: Downstairs boiler: Any help would be greatly appreciated

Hi Not sure if anyone can give any ideas - but I’ve got a Worcester Bosch junior 24i system boiler. For the past 10 years I’ve lived In the house - the average usage of gas has been about 10,000kwh. For the past 2 years my average has been 58000kwh. (Boiler is the only gas appliance in the...

Hello all, I'm currently in Ireland and in a small cottage where the plumbing system has me scratching my head a bit. When the place was done up the builders decided that the tank in the loft was no longer needed and put a tank out back in a small extension where ALL (well, except for the cold...

Hi there I am looking at changing my vented cylinder to an unvented 210L. I currently have a 30kw system boiler which I would like to continue using with the new cylinder. Looking at the various manufacturers of unvented cylinders, I see some of them have ‘high gain’ versions, such as Joule...