Search the forum,

Discuss Sweating cold water pipe in the USA area at PlumbersForums.net

Messages
2
I'm having an issue where I am getting a buildup of condensation on the cold water pipe in my home that is located in my kitchen.

I have insulated the pipe with plenty of foam but it's still doing it, It's then running down the pipe and down my stop tap and onto my wooden floor.

The cold water pipe feels absolutely freezing, much colder than it should be in my opinion and I can't understand why.

Any help would be greatly appreciated.
 
Quite typical for cold water to come into the house below 5°C and if the water comes in under the sink then any water used in the house will draw new cold water into that section of pipe. Worth checking, as others have suggested, that there isn't a tap or float valve (ballcock) dribbling somewhere.

If you have 20°C room air temperature at 70% relative humidity (RH) - this is quite a damp room - you'll get condensation on any surface below 12°C. If your relative humidity at that temperature is below 40°C - this is a reasonably dry room - then you won't start to get condensation until around 5°C. Either situation is possible in a typical British dwelling.

RH is a measure of how much water is in your air compared with how much water could be in that air at a given temperature. The temperature of condensation (i.e. 100% RH) could be reached at various temperatures depending on the amount of water dissolved in your air (i.e. ABSOLUTE humidity). You can look this up on a psychrometric chart if you know the temperature and RH. Or ask me 🙂.

Assuming the humidity of the room cannot be reduced, you either need to lag your pipe and apply a vapour barrier on the outside of the insulation (insulation tape or gaffer tape over the dry lagging would work) and your insulation needs to be thick enough to stay above the condensation temperature. The foam lagging probably doesn't need a vapour barrier, but if the joints aren't sealed then warm moist room air can get behind the lagging and condense on the cold pipe so you need to seal around the lagging somehow.
 
Have you checked for any leaks, dripping taps etc on the cold side?
When water is standing still in the network it will come accustomed to its surroundings temperatures, if there was a problem elsewhere you will constantly introduce cold water to the system will will cause condensation to form.
My hot water tap in my bathroom sink does not work (turns easily and nothing happens) and drips every couple of seconds, could this be the reason why I am having this issue?
 
My hot water tap in my bathroom sink does not work (turns easily and nothing happens) and drips every couple of seconds, could this be the reason why I am having this issue?

This could very well be the cause, if its constantly dripping then new cold water from your incomingmains has to make up for the loss. As Ric2013 said above, this is down to the science of relative humidity and dew point. His description above is very accurate.
 

Reply to Sweating cold water pipe in the USA area at PlumbersForums.net

Similar plumbing topics

    • Like
Hi I recently did some pipe insulating in my loft. The only two I didn't do were the vent pipes. Not sure if that is the right term for them? They are the pipes that feed water back into the top of the tanks when there is excess, presumably from steam, expansion, etc. The one going to the cold...
Replies
2
Views
331
Hi, I am probably being unduly paranoid here but I noticed under our kitchen sink that there is some corrosion evident on a small section of copper pipe between compression fittings on the hot water feed. There are take offs for an outside hot and cold tap together with isolation valves and...
Replies
9
Views
240
Morning. I have a leak. It’s coming from the connector pipe….the picture shows the pipe. It is a cold water pipe going in to the back of my dishwasher. I assume the washer may need a replacement. Anyway I cannot for the life of me turn the water off I.e at this cap. I understand I should turn...
Replies
2
Views
320
I need to cap off a water connection which is the water pipe connector to an M15 hose pipe from a kitchen sprayer tap. I have included images so you can understand my problem. Can anyone tell me the best way to blank off that pipe. (That's the vertical brass pipe in the photos)
Replies
7
Views
391
Where and how does the water supply work and is there only one rising main pipe and where is it usually located? I am top floor flat, mains fed supply and all 6 in the block have a shared rising main pipe (I think unless there is meant to be more than one). Kitchen: From the ground floor to...
Replies
2
Views
545
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock