Search the forum,

Discuss stopcock found after 30 years! in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Messages
21
My mum has just had a new boiler fitted and we found the stopcock sticking out the plaster behind the old boiler. I have been looking for it for ages so it was quite nice to finally find it. Do you think it is safe to try and turn it after putting some wd40 on it and leaving it for a while?
 
Picutre

IMG_0431.JPG
 
If it was in my house I'd try it but only if I had a free afternoon and there was a local merchant open or I already had all the parts I might need.
In a customers house I wouldn't touch it unless I was there specifically to fix it.
The only reason I'd touch it in my house is I know how to fix it if it leaks/breaks/falls off/explodes/opens a wormhole to hell and looking at that pic I'd say at least one of those things is likely.
 
Our outdoor one was down a hole and didn't shut the water off significantly, got the water board to fit a meter for free which comes with a shut off. No idea how they fitted it without getting soaked though.
In your case op i would just replace that one and replumb it outside of the wall too for that matter! No point leaving something like that in place as you wouldn't use it anyway.
 
In my road all company stopcocks, unless metered, are in the front gardens and not easy to find.

One house badly flooded when owner away and keyholder had problems finding cock in house.

Perhaps a notice just inside front door as to where to find cock would be helpful.
 
^^Yes yes...there is an all female plumbing firm called "stopcocks" why not give them a call to see if they like handling a stuck cock.

http://stopcocks.uk/
I couldn’t care less and good luck to them but I can’t help feeling if a bloke set up a company called noflangeplumbers or something there’d be uproar
 
got the water board to fit a meter for free which comes with a shut off. No idea how they fitted it without getting soaked though..[/QUOTE said:
They didn't!
I had them out to change a broken stopcock and they dug the hole, cut the main live with a petrol saw and then fitted the new stopcock. And yes, the fella got soaked.
It was quite funny because we were working on a ground floor maisonette and shutting of the stopcock turned the upstairs off as well. We warned the (big and burly) bloke upstairs who was ok ish about it as long as we were quick because , and I quote, " I've got me bird coming round soon and I need a shower and a s**t before she gets here"
So when the stopcock wouldn't turn back on he wasn't very happy. I sent the lad up to tell him.
Water board were out in a couple of hours though.
 

Reply to stopcock found after 30 years! in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hey all, Looking for some advice. My mother recently had her boiler changed but in the process the water had to be turned on and off as you would expect and the engineer broke of the handle. Luckily it seems you can close the valve with some pliers on the but I don't believe this is best for...
Replies
5
Views
210
    • Winner
    • Like
Hi all, I joined today and am a newbie at plumbing DIY. Thought I'd share my experience replacing the stopcock under my sink. The old one looked very corroded around the tap handle. An Anglian Water engineer was at the property measuring my water pressure and flow rate. When he saw the...
Replies
1
Views
497
Advice from experienced plumbers will be appreciated. I inherited the old stopcock without a disk (2 pictures below). Attempts to find a lever or disc with 8mm rectangular hole were unsuccessful and use of a locking plier was not convenient in emergency, so another stopcock was fitted after it...
Replies
1
Views
482
Deleted member 120897
D
Hello. I've just replaced our old Potterton EP2 CH controller with a Drayton Wiser HubR (& peripherals). The old backing plate wasn't compatible with the new universal one, but the wiring was pretty close AFAICT (N, L, 1, 3 & 4 connected) .When I first powered it up but didn't have any TRVs...
Replies
1
Views
243
What’s the correct way to replace a (jammed and leaking) stop-cock in an old and corroded ½ steel pipe without damaging the pipe? The pipe in question is a main water supply pipe for a house and dates from (I guess) the 1970s. It’s from a shared supply for myself and the neighbouring half dozen...
Replies
3
Views
813
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock