Search the forum,

Discuss Recommendations to stop limescale in the USA area at PlumbersForums.net

Messages
6
Hello there I live in a very hard water area I need some help to what I can use to prevent limescale build up etc. I looked around so many on the market and also mixed messages. I live in a one bedroom ground floor flat with wet room and toilet etc. Any advice would be much appreciated.
Thank you William
 
I live / work in a very hard water area (440 p p m) after trying various water conditioning devices fitted a proper softener at home 4 years ago.
Should have done it years ago ! Use far less soap/ detergent no salt in dishwasher clothes fell softer.
Even better no tap ball valve etc maintenance dueto scale build up! On balance I would say cost neutral to run .
 
Ditto - we live in a very hard water area too and fitted a softener when we refurbished our house 7 years ago - so no limescale for 7 years.

If you do go ahead, get a unit that senses the amount of water you use or your salt costs will be high
 
Another vote for a salt based water softener, nothing else will sort it for you.

However, there are lots to choose from and the danger is that, being a noobie, you might go for one of the cheaper ones. Buy cheap and you buy twice!

Do some research, buy the best that you can afford, and with care it will last a lifetime.
 
1. Agree with the others. A proper salt based, ion exchange type, water softener like a Harveys or Kinetico is the only real solution.
2. However, with a one bedroom flat, you may be short of space. An ion exchange water softener takes up about the same amount of space as a small dishwasher, and you need somewhere to store the salt unless you buy it as needed.
3. You could look at a polyphosphate type "softener". They don't really stop the limescale, but do stop it sticking to heating elements (e.g. kettle). Might be a second best solution.
 

Reply to Recommendations to stop limescale in the USA area at PlumbersForums.net

Similar plumbing topics

I was stupid enough not to check the position of the pipes under the tiles when installing a toilet and drilled right through the center of a 16 mm copper water pipe. I exposed the pipe by removing a ~30cm section of the plastic sleeve and a ~10 cm section of the pipe around the hole. Several...
Replies
0
Views
175
Hello, I am seeking some advice, I have a POTTERTON PROMAX 28 COMBI Boiler and I noticed yesterday that the water around the house is no longer warming up. The heat exchanger has been changed 6 months ago, so I do not believe it is that. Does anyone have any ideas on what it could be? Thanks
Replies
4
Views
212
Hi everyone, Looking for a bit of advice, recently went to a job where heating was operating when called for however not for the hot water. I have changed the 3 port actuator Honeywell head however this doesn’t seem to have solved the issue, does this mean that the programmer is faulty? Or is...
Replies
8
Views
224
Hello all, I’m replacing a concrete paving slab patio in the back yard. The original patio used 50mm deep concrete slabs on hardcore & sand. I’m planning to pour a 100mm deep concrete patio on 100mm hardcore. In order to achieve the same final height to line up with the rest of the patio, I...
Replies
6
Views
217
Hi, Can anyone advise as to why the cold water to my bathroom keeps airlocking? This originally happened about 12 months ago and has happened 3-4 times since. It’s an upstairs bathroom, fed from a tank in the attic. The tank is about 8 Meters away and feeds a bath, sink and toilet. The tank...
Replies
9
Views
304
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock