Search the forum,

John Lewis ceramic mixer tap washer replacement

Discuss John Lewis ceramic mixer tap washer replacement in the USA area at PlumbersForums.net

Mouse 5656

Mouse 5656

Messages
1
Hi I have a John Lewis kitchen mixer tap but can’t see the item name just JL. Does anyone know what replacement ceramic washer I’d need?
2B059C54-8B30-41C1-9D21-7A88EC44874D.jpeg
It’s approx 5-7 years old. Many thanks
 

Attachments

  • 3282BF77-5F5E-4487-B42F-7DF6E246162B.jpeg
    3282BF77-5F5E-4487-B42F-7DF6E246162B.jpeg
    475.1 KB · Views: 15
  • 4638F9A1-3F12-4707-A022-EAC658547D6B.jpeg
    4638F9A1-3F12-4707-A022-EAC658547D6B.jpeg
    510.4 KB · Views: 13
Probably 3 options available:
  • Speak to John Lewis customer service (I believe the taps could be made in Italy)
  • remove insert/cartridge, and take to merchants/diy chain
  • renew the tap instead of faffing about
good luck
 
Even if you found the make it wouldn't help much in identifying the cartridge.

It's probably just a standard cartridge that you need.
You'll have to remove the handle first and check the number of splines on the end and length of shaft, then get some from Screwfix or similar.

If the Screwfix don't match there are loads of suppliers online, just search Ceramic tap cartridges.
Or a local independant plumbing supplier.

https://www.NoLinkingToThis/c/bathr...agedredirect-_-plumbing-_-ceramictapvales#_=p
 

Reply to John Lewis ceramic mixer tap washer replacement in the USA area at PlumbersForums.net

Similar plumbing topics

P
Viessmann combi starts when cold, mixer, tap is opened
Recently had a Viessmann Vitodens combi boiler installed, quite often when the adjacent cold mixer tap is opened the boiler starts for a few seconds! Can anyone tell me what is causing this? And how to cure?
Replies
3
Views
192
ShaunCorbs
ShaunCorbs
S
Advice needed for a mixer Spray for kitchen ?
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
73
Lou
Lou
B
Brass tap body is leaking.
I have attached an image of the brass body within a tap. Having replaced a cartridge which has cured a leaking tap, I can see that there is a small leak from the brass body which can be unscrewed. Is there a seal behind the body? Thanks.
Replies
2
Views
291
Bp89
B
M
Central heating losing pressure all the time
Every two weeks or so I have to go and top up the system because the hot taps are running cold. Boiler display is flashing 0.6 bar and I fill up to 1.3. I've had an engineer look inside the boiler and he can't see anything wrong. I've checked the pipes all over the house and cannot see any...
Replies
1
Views
96
fowlerboi
F
C
Mixer bar fitting solutions?
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
Replies
1
Views
178
SimonG
SimonG
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock