Search the forum,

Discuss Help! I need a partial bath tap replacement in the USA area at PlumbersForums.net

Messages
7
Hello,

First of all please excuse my limited knowledge on plumbing!
so my bath tap has started dripping from the ceramic cartridge, It is a single lever bath/shower mixer tap. (See photo)
I have replaced the mixer cartridge with a new one but the sealing face for the cartridge is corroded and I believe is not creating a good seal, hence the drip.
I want to replace the tap but due to the position of it, I would have to remove the entire bath to access the upright spouts.
My question is, can I replace the part of the tap connected to the spouts and if so can any one recommend a suitable replacement?
The gap between the spouts is 150mm.
If you need any more info, please ask as I want to make the correct purchase first time.
Many thanks

Leo
 

Attachments

  • 919C811C-87AC-48FA-996F-6CE92BFE7887.jpeg
    919C811C-87AC-48FA-996F-6CE92BFE7887.jpeg
    120 KB · Views: 18
  • 3BB90255-ACC0-4126-8674-2016D6E929A4.jpeg
    3BB90255-ACC0-4126-8674-2016D6E929A4.jpeg
    107.4 KB · Views: 19
You could leave the tails/spouts in the bath and renew the top part. What size looking down on your tap are the centre to centre of the tap/spouts at the back? Is there a makers name on the tap? Do you have a combi boiler or just gravity hot water?
 
Last edited:
You could leave the tails/spouts in the bath and renew the top part. What size looking down on your tap are the centre to centre of the tap/spouts at the back? Is there a makers name on the tap? Do you have a combi boiler or just gravity hot water?
Bit hard to measure centre to centre at the back because they are oval shaped but sum where between 180-185mm (thats between the spouts mating with the bath). Between the spouts connecting to the tap is 150mm. Unfortunately no markings on the tap for identification and I have a combi boiler.
Many thanks
 
Like this measurement bottom image. If that is the same you could have a thermostatic bath shower mixer or a tap that connects the same as yours.
 

Attachments

  • grohe-eurostyle-cosmopolitan-single-lever-bath-shower-mixer-33612002-spare-parts-[2]-122593-1-p.jpg
    grohe-eurostyle-cosmopolitan-single-lever-bath-shower-mixer-33612002-spare-parts-[2]-122593-1-p.jpg
    31.2 KB · Views: 9
Like this measurement bottom image. If that is the same you could have a thermostatic bath shower mixer or a tap that connects the same as yours.
Yes the measurements in that picture are correct. Do you have any suggestions on where to get the tap from? All my searches from suppliers have failed to provide dimensions on their taps. Ideally I would like to just replace the tap for a like for like but I can’t find one 🤦🏻
 
Yes the measurements in that picture are correct. Do you have any suggestions on where to get the tap from? All my searches from suppliers have failed to provide dimensions on their taps. Ideally I would like to just replace the tap for a like for like but I can’t find one 🤦🏻
Do you know where your bathroom came from? If you do you will be able to buy the same. Take a photo. You said you bought the cartridge for the tap. Did they know what the tap was? I will take a proper look when I get in.
 
Amazon normally have decent pictures of there sizes

Cheap and cheerful


Decent

 
Amazon normally have decent pictures of there sizes

Cheap and cheerful


Decent


I didn’t even think to look on amazon for a bath tap! Those dimensions seem to match up with mine, so guessing they should fit. I’ll give the cheap and cheerful one a go and easy enough to return if it doesn’t.
Thanks for all your help everyone 👍🏻
 

Reply to Help! I need a partial bath tap replacement in the USA area at PlumbersForums.net

Similar plumbing topics

I have a plumber coming tomorrow to change a cartridge on a badly dripping tap on my bathroom mixer unit. There is no separate isolating valve for this tap so I'll have to close the stopcock. I tried closing it today but it won't go absolutely 100% closed and there is still a very slight flow...
Replies
1
Views
205
Hi, Can anyone advise as to why the cold water to my bathroom keeps airlocking? This originally happened about 12 months ago and has happened 3-4 times since. It’s an upstairs bathroom, fed from a tank in the attic. The tank is about 8 Meters away and feeds a bath, sink and toilet. The tank...
Replies
9
Views
249
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
Replies
0
Views
108
Hi All I have a leak coming from within my Mira Elite QT shower. It seems to be flowing from behind the switching Control. Any ideas what could be causing this leak. Already Changed the Pump Elbow as one of the clips had popped which was causing a second small leak, Any idea? Is it time to buy...
Replies
0
Views
202
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock