Search the forum,

Discuss Central heating pump does not start at first when cold / rested in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Messages
5
I have a Grundfos Ups2 15-50/60 pump, approx 2 years old (still under warranty) which does not start when the system is cold or has not been calling for heat for a while, eg. first thing in the morning.

It makes a clicking noise every few seconds, then the boiler overheats, boiler thermostat cuts out and air travels around the system. When the air/vibration reaches the pump it usually starts or sometimes it just starts after a couple of minutes. Then once the boiler cools and restarts the system works through the day, although at first it sounds as if the boiler is on the point of overheating, sort of pre-boiling sound like a kettle.

I have bled the pump and tried turning the impeller before it starts in the morning and all seems well.

I assumed it was a fault with some aspect of the pump electronics.

The plumber came today and said he has not experienced this before. He can swap the pump but does not know if this will cure it and is not sure it will count as a warranty claim because it works most of the time and will be difficult to replicate the fault.

Anyone come across this before?
 
Strange one, did the plumber check the electrics over? When power is sent to the pump it will start instantly. If electrics are all ok then a new pump will be required.
 
When the heating or hot water is calling for heat the three way valve operates and the green speed indicator light on the pump comes on but does not start. The plumber wanted to test if there was 240v present at the pump but before he could are the cover off the impeller started. The pump will run at all three speeds so is getting a supply once started and I assume if the green light is on then there is a supply as soon as the alive operates. I have only been aware of it in the morning and once in the afternoon. It is only apparent because of the boiler overheating sending air noisily around the pipe work including causing the water to come out of the expansion tank overflow. It seems as if it is caused when either the water in the pump has cooled or if it has been unused for a while. The house is occupied during the day and so the boiler is firing up frequently.
 
It's unlikely to be anything other than a faulty pump motor. If it's under warranty there should be reason not to swap it.
 
Thanks. That was my conclusion. It just seemed odd that the plumber was not sure so I thought they might be something else to consider.
It's probably the plumbers own confidence causing the issue. No one wants to wrongly diagnose an issue and charge for work that won't fix the problem and if he's not came across the issue before that will further add to his own doubts.
 

Reply to Central heating pump does not start at first when cold / rested in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Good afternoon, I am experiencing a pressure issue with my heating system and was hoping to receive additional insight as to what the problem could be. We have a biomass boiler and stratification tank set up and recently had an issue with boiler pressure dropping off when the system was cold...
Replies
9
Views
344
    • Like
Hello, my Mothers heating failed in the recent UK cold snap. I found the pump was stuck. I have a question about pump orientation. The existing pump flows downwards. The manual for the proposed replacement recommends that it should pump upwards. This would involve rearranging the flow &...
Replies
8
Views
606
I have a 2 pump hot water tank (Flomax 180L fitted in '94) in airing cupboard system with an Ideal classic boiler (downstairs next to an external wall) which for the most part seems to provide excellent hot water. The central heating also works fine - though sometimes I think the radiuators...
Replies
12
Views
663
I have been facing central heating low pressure on unvented hot water RM Cylinders but can't see any leak on the PRV, expansion vessels and plasterboard celling. I have got unvented pressurized RM Cylinders hot water system with 27KW Worchester gas boiler with expansion vessels . When...
Replies
2
Views
448
losing pressure
L
Hi, Short version: Do frost protection valves trigger when the water in the pipe gets to threshold, or when the air temp drops? Long version: I'd rather use frost protection + anti-freeze cycle on my mitsubishi ecodan heat pump. The warranty is apparently fine with that combination, and it...
Replies
3
Views
95
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock