You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
won't
The English modal verbs are a subset of the English auxiliary verbs used mostly to express modality (properties such as possibility, obligation, etc.). They can be distinguished from other verbs by their defectiveness (they do not have participle or infinitive forms) and by their neutralization (that they do not take the ending -(e)s in the third-person singular).
The principal English modal verbs are can, could, may, might, shall, should, will, would, and must. Certain other verbs are sometimes, but not always, classed as modals; these include ought, had better, and (in certain uses) dare and need. Verbs which share only some of the characteristics of the principal modals are sometimes called "quasi-modals", "semi-modals", or "pseudo-modals".
My double flush toilet has developed a fault. It won't stop filling eve when I pull the float arm right up. I have replaced the inlet valve diaphragm but this has made no difference
What else can i try?
Hi All
We have an oil fired Boiler, Tank in the loft and Hot Water tank in the airing cupboard with a Honeywell ST9400A control and HCW80 and HC60NG remote thermostat.
For a while the Hot Water was not coming on. We had to fire up the Heating if we needed Hot Water.
I swapped the motorised head...
Hi,
My aunt asked me to have a look at her Geberit cistern which recently has suddenly stopped flushing on the short flush button. Long flush works normally as far as I can tell.
This is the flush mechanism (the label suggests PN 7074-98) , please excuse the mess:
Took the whole thing...
I've fitted a completely new burner to a Grant Combi 70 and the motor will not run (so consequently the burner won't fire) despite there being live 230v power to the control box.
I have read the wiring diagrams and even spoken to Grant themselves but I cannot get to the bottom of the problem so...
We had a plumber install a high rise low flow (1.6 gal / flush) toilet about a year ago. It worked fine for about 6 months. Since then, the plumber has been here 3 times because the toilet won't flush properly. The plumber has used a RIGID tool. He has replaced the ball cock and cleaned the...
Hi having the same issues currently with back boiler, so far 2 different gas engineers have changed programmer and syncron motor to no avail although programmer change resulted in temporary fix. Coming back tomorrow to check it.
Hi, I have a Worcester greenstar Ri on a Y plan system with hot water cylinder. Problem I'm having is heating won't switch off once on, it ignores the room stat and programme and stays on. I've tried; new 3port motorised valve, new programmer/timer and also new room stat. I've also disconnected...
Hi,
Forgive my inexperience, I'm a first time buyer and unfamiliar with anything plumbing related. We had a washing machine delivered today and the supplier was unable to hook it up as the tap for the water inlet hose was so close to the wall that the wings on the connector on the inlet hose...
Hi - Our Rayburn 400K mainly runs low as a heater as we have LPG cooker. Yesterday (Christmas Day) I turned the control up to 8. It heated until the Thermodial needle got into the Roast sector, then it cut out and did not kick in again until it had cooled off - useless for roasting tatties! I...
Hello folks,
Our push button toilet won't flush properly most of the time, if you push the button it makes a half-hearted attempt, but gives up; sometimes you have to push it quickly 3 or 4 times and it eventually flushes; occasionally it just won't do a proper flush and you have to leave it for...
Hi all, new here so I hope I'm posting in the right place. I'm having a hell of a time with my bath drain cover. I just wanted to take it off to get a better look at whether the P-Trap was dry. So I unscrewed it. And it won't come off, but neither will it screw back down! Now I just want to...
Hi everyone, my kitchen sink plug won't stay open! It’s really frustrating. It’s held up by a little plastic hoop around the shaft, and friction is supposed to stop it closing. But it’s too easy to close – just running water will close it, and I have to hold it open all the time I want to empty...
Radiator is still getting hot even when the thermostat is set to zero. Turning the other valve does nothing. Both valves (the thermostat and the other one) are now turned as far clockwise as they will go and the radiator is still getting hot. Photos are below. Any help would be much appreciated.
Hello. I am sorry to open this with an admission: I made a dumb mistake and am seeking any help possible, thanks in advance ---
The pressure dropped on my boiler, so I opened the usual valve and let it climb up to 1.5 bars. I've not been in this house long, so the boiler is new to me. I closed...
Morning all,
I'm new and shiny here and seem to have developed a heating problem this morning. Any pointers for a quick resolution would be appreciated as my ears are now hurting! :rolleyes:
I have a Vaillant Ecotec Plus 630 driving rads, hot water and underfloor heating in some of the house...
Good afternoon all,
I have a Worcester boiler installed recently. It was moved from the first floor to the loft. Existing 22mm condense pipe was extended to the loft. It looks like the old pipe has no slope and prevents air to get into the boiler condensate trap, preventing condensate to drain...
Hi All,
Help. Very strange, but shower won't turn off. I believe its a Grohe Rapido T, picture attached. Managed to isolate it at the shower pump, although I think one of the stopcocks is broken, it just kept turning. Luckily there is a stopcock on the inlet and outlet pipes of both hot and...
Today I drained my CH/HW. This is a standard vented, pumped S plan with two electric valves, and I'm in UK.
I was lucky enough to have a drain valve underneath ground floor, relatively accessible, see pics:
However, upon refilling the system, I found out that that valve will rotate...
Hey guys. Looking for some advice on the best way to make my new range slide all the way in. Currently, the pipe and gas connector sticks out 6" from the wall. The range has a 4" deep recess. So I have to reduce the stick-out by 2". I was thinking about just removing the 90 degree elbow (circled...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.