evening folks, im putting an unvented in an old farmhouse in an upstairs room alcove area that will be eventually made into a cupboard.
being an old farmhouse, the floor is all over the place, I put a bit of fibreboard down and levelled it but the floor is out in a compound angle and is a real...
Hello,
We have just had a complete overhaul of our heating and hot water.
We previous had a conventional (?) system (two tanks in the loft, copper tank in the airing cupboard) heated by a Worcester Bosch 18ri. Controlled by a 3rd gen Nest.
We have changed to an unvented tank (Kingspan) system...
Matt Lucas
Thread
degree
hot
hot water
mystery
solve
system
unventedcylinder
water
Watch out for this one, haven't resolved yet. Put in unvented cylinder for customer who wanted long 25 year guarantee. Cylinder installed as vented as they were willing to pay the extra. 2 years on cylinder develops a leak and customer told by manufactures there is no guarantee as cylinder is...
what exactly is done in an annual service for an invented cylinder? Other than checking no leaks, immersion elements are ok etc
I have my G3 ticket. But don't be fooled, they don't teach you much on the course!!!
HI all,
I am currently in the process of having a loft conversion done, of which I need to upgrade/change the heating and hot water system as the house will be a 5bedroom with 1bathroom and 2 showerooms once complete.
I currently have a Worcester Bosch condensor boiler which is 24kw, which has...
jitno123
Thread
boiler
header tank
loft
oil
unventedunventedcylinder
Does anyone get involved in maintenance of UV cylinders?
Been sent this picture asking if I can have a look as it's leaking
Would you bother repairing a it looks to have multiple leaks and generally be in a bad state
Hello,
Having recently bought a new property which has an unvented hot water system installed, I'm just trying to understand what's normal and what's not so normal having had no experience of an unvented system in any of my previous properties.
My intrigue/concern really comes from when the...
Jimi
Thread
advice
cylinder
needed
normal
unventedunventedcylinder
Hi
I have recently had a unvented cylinder installed. The old water tank has been replaced with this system at a cost of £2500. Does that sound reasonable?
Thanks
Darren
Darren
Thread
cylinder
hello
installation
member
question
regarding
unventedunventedcylinder
Turned off mains, opened cold and hot side of kitchen tap, both stopped in about 30 seconds. Worked on toilet and changed some tap washers. Turned back on, all good pressure downstairs, hot and cold very poor upstairs.
Told her I'm not unvented so can't advise/deal with.
But did I do anything...
Guys looking for some advice
I have a property that we are working on we have the following
gnd flr
wc
kitchen with dishwasher and one basin
water softener
1st flr
ensuite
shower toilet and basin
ensuite 2
shower basin bath and toilet
2nd flr
shower
basin
toilet
washing machine
We have...
Hi all, I currently have a 15mm mains supply to a unvented cylinder in the loft as the pipe goes under a tiled floor en suite and it was not upgraded during the installation. I am now in a position to upgrade to 22mm but do I have to use a G3 qualified plumber for renewing the 15mm to 22mm...
Hello,
I have a Combi Boiler (Vaillant Ecotec Plus 428) and an Unvented Cylinder (Vaillant uniSTOR VIH GB 180s). Since yesterday we have no more hot water in the house, it comes out cold or luke warm. But the heating works fine.
When a hot water tap is fully opened, the boiler reads S.30 (no...
Hi Guys, just after some advice if someone could help.
I have a Aerocyl plus unvented cylinder in my house, Heat pump external (no gas)
I have a steady flow of cold water though the pressure relief tundish. Its constant as far as I can tell.
Going to call out a plumber tomorrow but in the...
about to hook up the flow and return to a santon cylinder that has been fitted for some time and using immersion only, the connections are not with the cylinder anymore, where can I get them?
does anybody know if the unvented cylinder can go in a loft or garage? Any problems with doing so?
Also, will my 14 years old boiler work with unvented cylinder or would I need to change the lot?
Thanks
looked at an install today and the pressurised cylinder cupboard ws completed in push fit. The tundish hadnt been conected yet but wht are peoples views on it. i personally only use copper but am told plastic is ok.
Eddie
eddiebrown424
Thread
copper
cylinder
eddie
fittings
pressure
push fit
unventedunventedcylinder
Ongoing issue thats never been fixed!
I am having issues with hot water flowing into the tundish, when the hot water cycle is running, is there anyone that can help?
Just decided on new heating system comprising of Vaillant system boiler and the latest Unistor unvented cylinder. The newer Unistor cylinders are B rated however OSO now do an A rated cylinder and was thinking long term the OSO should be a considered option. Going fully Vaillant I understand the...
good evening folks. hope all is well.
i really need some help.
a customers Santon PP 300e unvented cylinders heating elements had failed. i drained and replaced said elements. after allowing the system to re-fill and re-heat, i was made aware that the hot water was very hot, but that the hot...
i need to spec a unvented cylinder on a job,currently has a duotec 40 he combi that i am going to use as a system boiler,trouble is i have not done unvented installs for ages so need advice sizing up the cylinder i need,needs to cope with 2 bathrooms ,will be using a megaflow
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.