You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
tee
A tee is a stand used in sport to support and elevate a stationary ball prior to striking with a foot, club or bat. Tees are used extensively in golf, tee-ball, baseball, American football, and rugby.
I had a leak coming out from this reducing tee just after a month after installation.
I think it’s an old Hep2O tee.
I took it apart and found that the grab ring had scratch the PEX pipe.
Making me think the pipe had move out of its place.
Has anyone else have the same problem and any idea...
Hi all
I have a Vaillant ecotec plus (ground floor) and an unvented cylinder (top floor). This is an s-plan with a downstairs ufh zone and a single 1st and 2nd floor radiator zone each zone controlled by a two port valve. We have had various issues with the installer of this system.
The latest...
Hi all,
I suspect I've incorrectly used a tee in the flow return as the two radiators don't seem to get hot enough.
I have two radiators and their flow returns feed into opposing ends of a tee.
Like below.
Rad ----|---- Rad
Return
I think it should be like -
Rad -------|------- Return...
Hi,
Long story short: my boiler (gas, conventional, vented, three port system) has been moved from one side of the house to the other.
Previously the immersion cylinder return was the final tee before reaching the boiler, and all worked fine.
Now the immersion cylinder return is a few tees...
ok, I just want someone to clarify please...
3 tee rule..
Flow:
Cylinder
Heating
Bypass
Return:
Bypass
Heating
Cylinder
Bypass and cylinder to come off at right angles.
???
Taking Out A 28mm Tee to Replace With Connector On Pipe With No PLAY
How do i replace a 28mm tee with a connector when the pipes are rigid and fixed on both sides? I.E.. I can't pull the pipe together to get them into a push fit connector.
Do I replace a section with plastic pipe that will...
My stack appears to vent into the loft, presumably using an air admittance vent, as there are no odours coming from it until you lift off the vent. Can this just be teed into with a new branch waste pipe (inc. toilet and shower waste) or would I have to extend the pipe to the outside?
Hi, i'm installing a bathroom and need to install tee fittings into existing hot/colds. The best place to do this is near the boiler, however someone told me you cant use plastic pipe/fittings within a certain distance of the boiler. The best place for the tee would be about 2 feet away from the...
You can see the flow from the stove top middle and the return to the stove continues about a foot just behind the fridge and then turns back into the wall and stove just behind. Thanks
spudseven
Thread
correct
cylinder
injector
placement
return
stove
tee
water
Hi,
I'm attempting to extend the plumbing under the sink a little, as the drainage pipe on the new washing machine doesn't reach the spigot.
I've bought a mcalpine flexcon 4 pipe thinking i could just connect that onto the tee and then attach the spigot to the end of that. The problem is...
Hi all, I was hoping for some advice on how to run a new soil pipe for a new toilet in an extension, into the underground drainage? The customer said there is a old soil pipe there and he will dig it up for me, but what fitting do I use to tee into it if it's just a running underground clay...
Unregistered
Thread
110mm
drainage
oil
pipe
running
soil
soil pipe
tee
underground
just went to sort a dripping toilet what should have been a simple job just replace a straight pan connector with a offset. Simple right?????
first the flush broke
then the elbow falls out the tee and won't seat in properly ffsssssssssss
surely the elbow should be tighter then just pushed in
tommy1712
Thread
connector
elbow
flush
oil
should
simple
soil
soil stack
stack
tee
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.