You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
tails
Tails, or The Amnesic Incognito Live System, is a security-focused Debian-based Linux distribution aimed at preserving privacy and anonymity. It connects to the Internet exclusively through the anonymity network Tor. The system is designed to be booted as a live DVD or live USB, and leaves no digital footprint on the machine unless explicitly told to do so. It can also be run as a virtual machine, with some additional security risks. The Tor Project provided financial support for its development in the beginnings of the project, and continues to do so alongside numerous corporate and anonymous sponsors.
hi, we have a monobloc tap that is getting old, few years ago had the heads changed to ones with a leaver (for elderly person with artheritis) however now it has started leaking/ dripping, 1. tiny leak from the grub screw on back of the tap and 2. constant drip from tap itself, if we have the...
Hiya.Fitting a bathroom nxt week.There havin a shelf with a bowl on top & tap to the side fitted to shelf.The tap has flexi pipes to it which are around 300/500 mm long.Im running the feeds between the stud wall and was wondering which is the best way to connect the pipes,as i dont wanna fit the...
Hi, I have some new monobloc kitchen taps & they have flexi tails with a female threaded fitting with a flat rubber washer, can I simply screw them to an isolating valve (having discarded the valves olive & nut) ?
Thanks
Hi
I have a Astracast Elera 772 mixer tap & am confused by how to fit the stainless flexi supply pipes (instructions are about as much use as a chocolate teapot:D).
There is a threaded section about 75mm long & 30mm wide, the threaded holes for the flexi's are down at the bottom of that, how do...
notaclue
Thread
flexi
inside
job
mixer
mixer tap
pipes
screw
sink
smell
stainless
supply
tails
tap
water
wide
anyone had any problems with putting the valve tails into bottom of towel rads?
customer got the towel rad from b&q, when screwing in the tails for the valves they seemed to tighten in to far so the spanner hardly grips and they seemed a bit loose. i couldnt get them tight.
took them back...
pauls
Thread
diy
fitting
leak
plug
rubber
seal
tails
towel
towel rad
valve
valves
vent
Hi
I have looked on the forum and the internet (including vidoes) but I am confused.
They say to start at the open end going clokwise around the thread (or it will undo as screwed in) for approx 10 turns but do not overlap.
If the thread is longer than the tape width do I simply run the...
plumbinguser
Thread
internet
leak
radiator
rubber
tails
tap
valve
washer
waste
irs just occured to me after having a call ten minuites ago from an existing customer. he has a loud banging on his central heating system, more at the boiler side than any where. he called out home serve and was told he has got debris in the system and it needs powerflushing.
he then called me...
REDSAW
Thread
air
banging
boiler
boilers
central
central heating system
cold
connect
expansion
flush
flushing
job
power
problem
pump
radiators
system
tails
tee
valves
vent
website
work
Hello
I have just installed a fancy vertical rad, the problem is only half of it is heating up :confused: My suspicion is faulty TRV which is Drayton TR4 which I bought from ebay :o
I have bled the radiator and actually removed the bleed nut so as to get hot water into the rad. But soon as...
dollarbill
Thread
bleed
boiler
central heating system
cold
combi
connections
diy
drayton
flow
high
hot
hot water
inside
problem
radiator
replacement
sealed
stock
system
tails
tank
trv
vertical
water
Hi,
I have hired a Norstorm proflush, as i was going to powerflush my new radiator system. However the connections i have been given with the powerflush machine don't fit on the flow and return pipe of the central heating system.
Below is the fittings i have received.
These are the 3...
rockinter
Thread
22mm
adaptor
boiler
central
central heating system
combi
combi boiler
connections
diy
flow
flushing
head
help
pipe
pipes
power
pump
radiator
remove
system
tails
test
water
work
Recently when I was installing some taps I had a little weep from the copper tails and just could not stop it. So I removed them to have a look and found that it appeared the lsx had in some way deteriated the o ring.
Many I am sure dont use lsx in this situation but I have always applied a...
Today has been a nightmare getting trvs/rad valves that have been on for 35 years :(. Fill the system and two leaks from the the top of the nut at the bottom of the valve. Could this be from the nut being expanded from when they used hemp all over the place.
Would it be easier to cut and put...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.