You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
stick
The Memory Stick is a removable flash memory card format, originally launched by Sony in late 1998. In addition to the original Memory Stick, this family includes the Memory Stick PRO, a revision that allows greater maximum storage capacity and faster file transfer speeds; Memory Stick Duo, a small-form-factor version of the Memory Stick (including the PRO Duo); the even smaller Memory Stick Micro (M2), and the Memory Stick PRO-HG, a high speed variant of the PRO to be used in high-definition video and still cameras.
As a proprietary format, Sony exclusively used Memory Stick on its products in the 2000s such as Cyber-shot digital cameras, Handycam digital camcorders, WEGA and Bravia TV sets, VAIO PCs, early Walkman digital audio players, and the PlayStation Portable handheld game console, with the format being licensed to a few other companies early in its lifetime. With increasing popularity of SD card, in 2010 Sony started to support the SD card format, which was seen as a Sony loss in the memory-card format war. Despite this, Sony continued to support Memory Stick on certain devices.
Hi, I am trying to replace my washers but on one tap the screw I can’t remove and the second. Removed screw but I can’t pull of the handle :/
Does anyone have Any ideas ?
Kind regards
Our attic water tank (which is boarded in and not easily accessible) decided to stop filling up today... (we couldn't hear it filling up) and with the temperature outside reaching 32+ I am wondering if this might have caused a problem. The temp this evening outside has gone down to 21 degrees...
I currently have a 28mm Honeywell 3 port valve that works, most of the time, occasional blip by ball sticking or staying mid position or whatever. I have a pair of 28mm Honeywell
2 port valves and have contemplated for a while ditching the 3 port and fitting these. This obviously entails some...
Hello all,
I wanted a bit of advice. i have done the level 2 diploma in plumbing and also the nvq 2. I will be completing the level 3 diploma this year. My question is this.
Do I do the nvq 3 which takes 2 years and includes gas and unvented or do I stick with nvq 2 which makes me fully...
Have a landlord and appliance shop owner who I fit cookers and hobs etc for who's currently turning old shops into a couple of flats. I've put in the cylinder and tanks and new cold water mains but was not asked to fit the bathrooms which I couldn't understand. He wanted the so called builder to...
Hi everyone.....thanks in advance for any help with this. Replaced some trv valves on downstairs radiators...( two down and 3 upsatirs) no heating now for 3 days.
F and e tank empty at mo.
I have a small magnet on pipe above pump and it sticks all the way from pump to the t junction...
Hi
Currently using an Regular Oil central heating system with water Cylinder and water tanks in the loft. Unfortunately our oil tank has a big crack in the top of the tank, so will need replacing.
Only problem is, we can’t decide wether or not to stick with oil or move to LPG.
The situation...
Hello folks!
Right, here's the plan of my 1 bedroom, ground floor flat I'm refurbing. It is about 850sq ft in total.
[won't let me insert image from PhotoBucket - radiator image is incorrect, can't delete it] :(
In that image, rad positions are marked in red, going with decent rads, so...
Hi all.
I don't normally fit these sinks but recently been doing them on a council job. The sinks are supplied with the rubber strip that goes underneath the edges. Do you lot bother using the rubber/sponge strip or just silicone? What do you treat the edges of the work top with on the cut out...
I service a load of boilers at a school. In one boiler house (for dorms) they have a Grant 58/70 for CH and a Combi 70 v3 for DHW only.
The combi has been neglected and is, as you would expect, a rusted sieve.
DHW is required in 2 showers and 5 basins, 1 bath.
I suggested we just stick an...
I am re-sealing a (builder installed) bath.
It has some whacking gaps to the bottom of the tiles and so it will take far more silicone than is ideal (& using my referred BAL microban it will be £20 seal) so...
Is there a way to pack it out (a little) first with ano cheaper sealant - acrylic...
Hi,
I have just bought a new house, the heating is shot which I knew so we are ripping it out and starting again with a combi and a 2 zone system (upstairs and down)
The existing installation had the boiler upstairs in a cupboard but we want are going to move it downstairs to what will be the...
I am not sure what the actual ne of this tool is but it looks like a pen. You stick it on the shraeder and it tells you the pressure. In bars. Does anyone know where I can purchase one of these?
Cheers chaps
just bought wet vac
how do you connect up to wet vac for draining rads
is it hose pipe say a meter lenth stick in vac flexi tube and tape it to seal hose to vac flexi tube
or is there a connection to buy thanks regards dd
HOW DO YOU CONECT VAC TO RAD AS FLEXI PIPE TOO LARGE TO STICK IN RAD...
Hello All.
Just a quick courteous introduction before I get active onthe rest of the forum… I’m a “career change” plumber, so I know lots ofexperienced guys will be rolling their eyes, huffing and puffing about me (andthat’s just the ones I’ve met face to face). That being said I don’t...
Hi all, is there a minimum height for a washing machine waste trap (jockey stick type)? Seem to recall that it should be no less than 18". Went to a job today where the length was about 10" max, washing machine had been backing up unnoticed for weeks till flat owner below returned from holiday...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.