Grant Vortex 50/90 condensing oil boiler where the air tube spigot over the fan is not connected to the existing flue, should this be closed off with a Reillo cover plate to stop vermin getting into the open fan motor.If is blanked over will need a further combustion test to confirm adequate...
I need to pick someone's brain. Let me start with the events that led up to having no water. I have an old farm house with outside well running to the pressure tank in the basement. There is an outside water spigot about 7 or 8ft away from the well cap. The handle on the spigot froze and was...
I'm trying to pull a Polypipe SA62B access plug and cap out of the soil vent branch (which I think is a Floplast SP190). It's a bit of a cramped space and it feels VERY stuck. Any suggestions?
I'm removing it so I can fit a pan connector.
Three years ago my contractors installed my new SVP...
Hi All, I recently moved house and the waste pipe in my new home is significantly smaller than my last. It measures 25mm. I am having trouble decifering which sized spigot to get and I'm also having trouble finding anything smaller than 35mm (which bought and is too big).Pics attached. Advice is...
I'm a DIY homeowner repacing an outside toilet pan to a salt glazed spigot in a concrete floor. My guess is to cut through the mortar surrounding the spigot and continue cutting through the spigot. What are the pitfalls and tips to assure a clean cut through the spigot. Further will a plastic...
The drain cock on my water cylinder is very close to the ground and is obscured by piping installed by the previous owner. The spigot is at the bottom but, try as I might, I can find nothing to tighten it. Can anyone offer any advice ? Thanks
There is a utube of chris fitting his device, anybody know the reference for it. Some of our records have been 'lost' by BT and Chris is one ....thanks in advance centralheatking
he is part of an outfit in Bexleyheath
Hi all,
Is it possible to replace the s-trap under the kitchen sink with one that has a spigot, so that I can install a dishwasher?
That only traps I can find online with waste spigots are p-traps
regardsu
Hi,
Flowplast,pushfit, soil pipe double socket 92.5 bend.
New soil stack for new second floor toilet
Looks like I need to make a bigger hole in outside and inside wall so that the sockets go into the hole through the wall to match up with the pipe clip distance on the outside stack....
Am I...
Hi, Sorry for posting the obvious to the more experienced of you, I've just come across a meter in a box with the gas pipe going out through the back via the spigot, The transporter had apparently come and changed the regulator a couple of weeks ago, my issue is that there is a lot of what looks...
hello lads,
I am stuck with a question and I believe y simple but I cannot find an answer except from guessing.
Here it goes: when would a flue spigot restrictor be used on an open flued gas fire ?
I couldn't find the answer in my logic book but I'd would guess it's either when using a...
Hi all, I have a question about the best way to connect my soil pipe to a new "concealed everything" close-coupled WC (that has already been bought and is on site).
The soil pipe enters the bathroom from the stack for about 1.3 m alongside the wall (clipped against the first joist that runs...
Any one know supplier where I can get chrome compression spigot elbow to go 15mm copper, can only find push-fit ones. I need it for radiator tails but I am using chrome plated copper so push fit will not work, also need them by Thursday:(
Help appreciated
Hello
Geberit WC frame has a spigot outlet as per picture [frame removed for clarity!] with a 90mm OD. Fits rather baggy in the McAlpine WC connector that has a quoted inlet size of 97-107mm. The seal measures 85mm across and does seal the joint albeit not very tightly.
I would feel more...
I'm about to connect a replacement electric shower.
The shower has a 15mm plastic spigot and the cold feed has a 15mm brass compression joint.
I've read I should use a new copper olive, but should I also use a jointing compound or ptfe on the olive to ensure a good leak free connection.
Any...
Maxrob
Thread
brass
compression
compression joint
connecting
electric
electric shower
joint
plastic
shower
spigot
First-time poster and plumbing ignoramus, so please be kind....
I have a leaking toilet pan connector. The leak started when there was an old Multikwik connected.
I called a plumber and he tried a few different connectors and they all leaked. He said the spigot coming out of the toilet pan...
pulck
Thread
bathstore
connector
leak
oil
pan
pan connector
right
size
spigot
standard
toilet
Hi, a conundrum for you.
Currently I have a washing machine which drains into a high level standpipe and trap, 32mm which goes about 2metres to an outside drain. Now, I want to add a dishwasher to this arrangement. Uprating the diameter of the pipework is the first obvious point. But can I...
sparkspark
Thread
common
dishwasher
machine
pipework
spigot
washing
washing machine
Afternoon ladies and gents,
I've been having some issues connecting a used Bosch Classixx dishwasher to a waste spigot attached to a sink trap.
The waste pipe doesn't have the usual rubber end that I can jubilee clip over the top of the waste spigot. It is hard plastic and the same...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.