Which is the best push fit for continuous use (for testing) Has anyone found a pushfit thats good for testing use, there's nothing worse when testing all ok then you cannot remove the bloody thing, i have to cut several off and get them off in a vice.
Cheers
steveafoss
Thread
after
prefer
push fit
remove
speedfit
testing
whats
Fitted a new bathroom suite today and swapped the plastic pipe over for copper. No inserts used and customer tells me its been used for years with no leaks...
Any opinions on this as i was under the assumption that it would leak if no inserts were used,
thanks
eveneing all......just a quickie to ask if speedfit fittings will grab onto "chrome on copper" pipe?? tried one earlier and couldn't for the life of pull it off....anyone had any experiences doing this??
cheers.
should i be using metal inserts when using compression fittings with plastic pipe? thanks men
also any plumbers working christmas day then,, i bet some of u cant resist.. ha
I plan to terminate 2 pipes which used to provide a water supply to a washing machines and would liek to terminate them / in the concrete floor. I do not intent to re-use these.
I have 2 x 15ml speedfit stop ends for the pipes (they are plastic) and I am wandering if I can simply cut the pipes...
I have the following installed downstairs and am looking for an experienced plumber/engineer in Lincoln. The system works but since last winter a couple of rooms do not appear to be warming up correctly
Paddy
Lincoln
07545137271
Paddski
Thread
heating
lincoln
required
speedfit
ufh
under floor heating
underfloor
underfloor heating
Evening All,
But of advice please guys....
Started first fix on a bathroom refit today and discovered flow to (CWSS) cold bath feed is terrible to say the least.
This is now the 2nd time first fix has been done as "plumber" previously c*cked things up so took out his handy work & reran...
Hi all
I'm in the process of fitting a new bathroom suite for my nephew, anyhow i was advised on using speedfit
pipe as it would cut down on time and save messing with solder etc.etc, i have started to lay the pipe
under the floorboards but one of the pipes rests very near to a hot CH pipe, my...
Last year sometime I went to an emergency caused by a failed Hep20 fitting, the grab ring (green) had become very brittle and was in little pieces inside the fitting, it also crumbled in my hand. The pipe was mains hot water by unvented cylinder.
Kind of forgot all about that until yesterday...
For the first time I had a failure with Speedfit resulting in a fitting blowing off behind a bath on the hot supply. I had connected speedfit pipe to a flexi tap connector and used the correct TS insert and the fitting was properly compressed.
The only things I can think of for the reason for...
Hi
My question is regarding Plastic push fittings.
What in your opinion is the best Plastic fittings to use.
I am fitting a Shower it is running off a Combi , the reason for the plastic is accessibility .
Also I have ben reading about Collet grips for flo-fit gear. My other question is about...
Hello, I'm new to the forum and I would be interested in any views regarding the use of plastic piping for the central heating from a gas combi heating and hot water system. I'm renovating an old town house and I'm thinking of using John Guest Speedfit rather than copper.
Thanks and I look...
squashabe
Thread
copper
heating
hot
hot water
pipework
plastic
properly
speedfit
water
which
Hello
I put an outside tap in for someone today, i tee'd of the cold feed to the cold tap in the kitchen using a speedfit tee onto the copper.
I connected everything up & turned the mains on and the connection to the tap was leaking at the speedfit joint.
I thought i had pushed the pipe in...
hello
i'm after a few opinions really to get some idea which way to approch a job.
Im estimating for a full heating system from scratch. The customer has warm air heating but its just been condemned so no rads anywhere. They are happy to have rads but done want any pipework on show so the...
Need to join onto them to run supplies to a basin.
They end caps are not speedfit. Possibly pipe life or plumb sure or one of the others. Customer doesn't know.
My question is - Since I can't tell what make the plastic pipe is - how do I know what inserts to use on pipe if joining on with...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.