Hi.
We want to replace our shower tray. I've been doing lots of research trying to establish which trays are best. The current tray, I think is one of the really lightweight ones, is it acrylic? I like the idea of replacing with another acrylic, because it's lightweight and im guessing easy to...
Hi. I have have purchased 3 Mermaid wall panels to replace the tiles in our shower. These panels are 3mm in thickness. After removing the existing wall tiles, I have discovered that there is a gap around the entire shower tray, in some places the gap is greater than 3mm, the thickness of the...
Our shower room has been replaced and finished last week. The shower is an 1800 tray with the drain at the front. On using the shower we are finding a puddle at the back right which is never going to drain as it appears the tray slopes backwards when checking the edges with a spirit level.
This...
New shower tray and waste recently installed and thankfully have a cut out in ceiling below from when I was checking it's initial seal, when I spotted yday foam (from shampoo/shower gel) escaping from underneath the shower tray, out the sides of the waste.
I never really liked the initial seal...
I am about to fit a raised shower tray and wonder if I should concern myself with putting some kind of waterproofing material in the hollow underneath the tray e.g some kind of membrane? If so, what would be used?
Hi there,
I bought this 1500mm X 800mm X 30mm grey slate shower tray.
https://www.sonasbathrooms.com/en/slate-1500-x-800-shower-tray-black-with-free-shower-waste.html
It will be installed on a raised bed of 2.5 inch concrete blocks, and I might put a sheet of 18mm Marine Plywood on top of...
I’ve got to take out an old acrylic 600mm wide bath and replace it with either a similar sized one or a shower. Has anyone any source of either a bath that’s up to 600mm wide and under 1700mm long or a shower tray that’s 600mm wide and 1000-1500mm long. Really struggling to find anything...
I have a stone resin shower tray which is, admittedly, more than ten years old and I have noticed a line of small blisters that have formed under the surface as shown in the picture. They are each only a few millimetres but their alignment alongside one of the tray contours makes me think it’s...
Hi all
I'm looking for options for a 1300 x 760 shower tray - I've found a few but just wondering if anyone knows of any others out there. Ones I've found so far
- MX Elements. Available all over the internet
- Eastbrook Volente
- E:thos, from a company call bathroom-place/bathco, which have...
So I'm looking to replace my current shower tray as it has cracked. It is one of those long rectangular low profile trays as the ceiling is sloped so not too much height to work with & is in a downstairs bathroom & I believe it is a concrete base. I'm just looking for some advice as to any...
Hi I've fitted the above that has a 400 fixed panel and the sliding door which means the door is restricted to opening 400mm. The customer is unable to enter it as he is not small enough, so l will have to adapt or replace it for him.
Its on a sit on 100mm high acrylic tray, another point he is...
I’m about to install a stone resin shower tray, the tray (RAK Feeling) comes with a warning not to use cement for setting on and instead recommends silicone or PU foam. A few questions;
Has anyone fitting this or a similar tray with PU foam? Or is best to use silicone? Which PU foam or silicone…...
Hey there,
I purchased a black slate shower tray from a supplier. The supplier recommended that we cut it down to our required size. Is this good practice/possible? Some plumbers I speak to say absolutely not to. Others seem OK with the idea.
I hope to cut it down to around 1600x700. Cutting...
I have just received a resin capped shower tray and as best as I can tell, one corner at the back (i.e furthest away from the trap), is 3mm lower than the other corners. To be clear, this is across the top of the tray over which the tiles will be situated, although 35 mm of the edge will still...
I am really struggling with how to do the waste pipework from a shower tray and would appreciate any advice on the best approach to take.
The tray will be sitting in a three sided recess which really complicates things. A further complication is that the soil pipe is very close by and so there...
Hi guys,
Fully ripped out an old bathroom and installing a new one.
Getting mixed messages from Plumber and my father who is a Joiner/Carpenter
Plumber wants to fit shower tray before the walls are plastered.
Father thinks that the walls should be plastered first, he has left enough clearance...
To make fitting of the trap pipework simpler, I’m considering turning the rectangular tray around such that the trap would be positioned behind the user i.e. the water would flow away from the shower. Is there any reason why I can’t do this / it’s unadvisable?
I was wondering if a shower tray that has a upstand on all four sides would allow a semi enclosure. The shower tray will be sat against two walls but I am just confused to how the two shower panels will fit against the walls with the upstand being all the way around?
Any help would be really...
I'm looking to replace a shower tray that has cracked & is popping all over the place (guess previous owners had a bodge installation done). It is one of those low profile trays with the waste in the middle in a downstairs bathroom & is tiled around it. I'm looking at the Mira flight trays but...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.