You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
install
CONFIG.SYS is the primary configuration file for the DOS and OS/2 operating systems. It is a special ASCII text file that contains user-accessible setup or configuration directives evaluated by the operating system's DOS BIOS (typically residing in IBMBIO.COM or IO.SYS) during boot. CONFIG.SYS was introduced with DOS 2.0.
Went to see a job today where a boiler had been disconnected because of the flue.. see the pic, was shocked when I saw it.
Anyway, turns out an inspector from Gas Safe Register was the one who attended and ID'd it. But also the installer didn't register the boiler for building regs compliance...
I have a Worcester Greenstar 30Si and I'm trying to install the Nest Thermostat. I'm under the impression the case is a sealed unit can anyone confirm that for me please?
If so, can I get to the wiring without breaking the seal. I'm fine with electrics but boilers aren't my thing and I don't...
Hi
I need to install an unvented cylinder along side a Worcester green star heatslave 12/18.
cust wants the boiler to supply hot water to the kit tap and the tank do a bathroom and cloak.
is it possible to wire the tank and zone valves back into the boiler to allow operation?
we will have a...
Hi We have just been allocated a sheltered bungalow by our housing association, it has a newly installed gas service and also a new boiler an ECO Combi Compact RF not sure if it is a 24, 30, or 36.
The boiler is plugged into a standard kitchen wall socket there is no room thermostat or timer...
I need some advice please.
I have had several quotes for a central heating and hot water installation for a large 3 storey house with 22 rads (inc towel rails) but the advice I am receiving is conflicting and just wanted a bit of insight please.
Chap number 1 suggests 22mm flow and return in...
ArchieC
Thread
advice
boiler
floor
flow
flow and return
house
install
number
return
Good evening gentleman.
This would be the first post of many. As I pick up DIY myself, I am immensely interested in the aspects of plumbing.
This post is about that, and also so I can wear the proverbial other mans shoe (my plumber) before I think irrational things.
So, I have a 25 year old...
Got to install a magnaclean on a boilermate and flush the system.
Would you guys install it on the return to the boiler. Or the return from the rads?
Not sure which will pick up the most muck.
Hi,
I'm a diy plumber who is replacing and relocating the vented indirect HWC. I've ordered this copper unit from Gledhill but when coming to install it have noticed that the coil inlet / outlet ports are not in line. The top port is about 10mm back towards the cylinder and points slightly up...
andyzplace
Thread
cylinder
gledhill
hot
hot water
hot water cylinder
install
tap
vented
water
years
Hi All,
i am not a professional and all I can do is a bit of diy here and there. However to have mybarhroom updated I called a local plumber who calls himself a bathroom specialist. They have had few good reViews hence nothing suspicious on my mind.
I have a problem with shower enclosure they...
Hi all.
When you guys install the Nest heat link on to a wall, how do you wire it? In regards to the fact the wiring enters from beneath the box which makes it look untidy?
Hi folks.
I have a relatively small kitchen with a washing machine next to the sink. I want to put a dishwasher in but the only place for it is opposite the sink. This raises a few issues with how the dishwasher waste pipe would work...
1) Would it be better to put the washing machine opposite...
JohnthePainter
Thread
dishwasher
install
machine
sink
under
washing
washing machine
waste
Hi.. I am having my kitchen remodelled and the plumber has replaced the copper piping with PE-X piping to feed the kitchen sink water supply..
My question is..... He has laid the hot and cold pipes next to each other in the floor and concreted straight on top and tiled above, is this the...
Hi. I'm basically an electrician, but we do need to do some of everything in this world.
I'll begin by saying I've installed several shower pumps before, always successfully, and always using "good practice" with a air-free flange and separate shower pump feed from the tank. No problems yet...
Hi all.
I've got a Worcester 28i junior with a mechanical clock and room stat.
Wiring wise, what would be an easy swap over to a more modern programmer/stat?
I'm not to used to wiring up.
Any advice appreciated.
Afternoon all:
Following my other post http://www.ukplumbersforums.co.uk/central-heating-forum/93051-boiler-recommendation-2.html and now 3 weeks without heating/hot water homeserve wrote my gloworm 30cxi off. The engineers report said that the reason the boiler had failed was due to the...
Hi, I recently bought a Mira Platinum shower system and have just installed it. Installation went fine and is fully operational. Next, I unpacked the controller and followed the manual re. fitting batteries and pairing etc. As the last battery was inserted the display fired up with "r03" for a...
woodstockGaz
Thread
about
controller
display
install
issue
mira
platinum
power
Morning all quick question
I was always of the impression that a meter piped on double anacondas was wrong. Just come across this but gas safe have said its fine as long as it's on A meter bar.
I don't really mind either way as I've already found enough on this system to condemn the...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.