heat exchanger

  1. I

    Heat Exchanger with AGA and heat pump

    Hi All I have a client asking whether they can still use the AGA to heat rads once the air source heat pump is in. I think it is possible using a heat exchanger so the low pressure AGA and high pressure heat pump systems don't connect. I've seen it done on biomass systems but wonder what the...
  2. J

    Rounded screw on plate heat on a baxi duo tec

    Has anyone come across a rounded screw on a plate heat exchanger on a baxi duo tec and not been able to get it out? How did you overcome this on what is essentially an easy job. If possible I don’t want to have to take the whole manifold out on the right
  3. E

    Snapped screws on heat exchanger require a whole replacement?

    We just had a service done on our Ideal ICOS boiler and were told that the 2 screws on the back of the heat exchanger have snapped off. It was marked as dangerous and has quoted a whole new heat exchanger as there are still bits of screws stuck inside that cannot be removed. For 2 broken screws...
  4. D

    Faulty heat exchanger

    Hi, Boiler is losing pressure, from 1.5 bar to 0 bar in about 4 hours. Have checked all rads and seem to be fine, no water out external prv pipe. If the heat exchanger is faulty what do I need to look for? There is a constant run of water from the condensate pipe when heating on but not sure...
  5. 50Cent

    Tiny leak from heat exchanger

    Hi everyone, I have taken out the heat exchanger because a tiny leak was found around the red gasket at the top of the heat exchanger of a Worcester Green Star 28i Junior. The gasket itself is in perfect condition with no cracks. As you can see from the photo, the rust is near that holding...
  6. G

    Multiple thermostats and heat exchanger question

    I have a thermal store heated by a boiler with its own thermostat. I also have a stove with a back boiler. The stove heats water in a separate tank. There is a thermostat on this second tank that pushes hot water over to the store tank when it's hot. It's a closed loop and goes through a heat...
  7. B

    Main heat exchanger overheating when heating off

    Hi All, Have a peculiar problem with my Gloworm Flexicom 30cx combi boiler, the main heat exchanger is getting red hot and fault coding on overheat even though the boiler and central heating is not on, i shut the boiler down for a while, clear the fault code and it will be fine again for...
  8. H

    Best way to clean a heat exchanger

    I have a central heating system in a 7yr old ‘Persimmons’ new build, that has several problems related to reduced flow. A nice retired engineer on these forums, has helped me, through extensive testing, identify the heat exchanger as the culprit. The boiler is a Glowworm Ultracom 24hxi, 10...
  9. R

    Baxi 105e plate heat exchanger upgrade

    Hi all New Diverter valve going in mid week ( subject to eng being available) and from my previous discussion, the dhw plate heat exchanger could also be causing the bypass to lift. So I have sourced a potential replacement dhw plate heat exchanger to go in at same time, but the original part...
  10. M

    What is this material in my Heat exchanger

    Main Eco Compact boiler installed 18 month ago, system power flushed immediately before and straight after boiler installation, Magfilter 2 and inline descaler installed at same time. Boiler has just failed with blocked plate heat exchanger on the DHW side, heat exchanger cleaned and everything...
  11. B

    Glow Worm Fuelsaver 40B Mk2 Heat Exchanger Kettling

    I have an old Glow Worm Fuelsaver 40B Mk 2 installed on the kitchen wall. In November, the heat exchanger began making a kettling noise. It’s done this before. In the past, simply draining and refilling the system to flush out loose deposits was enough to stop the noise. In November 2021, I...
  12. L

    Is a pool heat exchanger suitable for a communal heating system?

    Hello all and Merry Christmas, We are in the process of planning the replacement of our 50-year old heating boiler serving a residential block of 12 flats with a total of 60 radiators. It is a vented single-pipe heating system, which has not been properly maintained, and we only recently...
  13. A

    Small cracked heat exchanger really an immediate do-or-die-NOW problem?

    I wrestle trying to get my mind around the claimed dangers of a heat exchanger with a small crack in it. I know salesman LOVE it, as it is very convincing to homeowners, and since personal safety is implied, it's pretty much a "signed deal" for a new furnace. I believe I have so much evidence...
  14. C

    My grant 70 mk 2 heating pressure is constantly increasing in pressure. I have changed the heat exchanger

    My grant 70 mk 2 heating pressure is constantly increasing in pressure. I have changed the heat exchanger as I believe that was the problem. Any ideas
  15. Atanas Peev

    Heat exchanger problem

    Hello everyone do any one had such experience with main heat exchanger on combi boiler Thank you
  16. G

    Power flush before blocked heat exchanger renewal ?

    Evening All We are having a new heat exchanger fitted to a Veissmann boiler, the boiler is only six months old, the installers carried out a power flush but only after the boiler had been running for about a fortnight, then after six months it failed to heat radiators to temperature. Viessmann...
  17. L

    Heat exchanger for new boiler on legacy open vent system

    Hi, We are planning to replace a 50-year old boiler for the communal heating-only (no hot water) of a residential block of 12 flats with 60 radiators. We have an open vent system. Our heating engineer recommends the GB162 100KW, WITHOUT a plate heat exchanger, because he says that heat...
  18. G

    Baxi duo tec 28 heat exchanger problem

    Our boiler went off with error 133. I investigated and found the ignitor module had melted! This was replaced. When the boiler fires up now there is intense and immediate heat radiation from the left upper and lower front side of the heat exchanger unit. I switched off immediately and have a...
  19. S

    Hi have a potterton performa 24he hot water flow is very slow. Have changed plate heat exchanger and made no difference any ideas?

    Hi have a potterton performa 24 he hot water flow is very slow. Have changed plate heat exchanger and made no difference heating is fine any ideas?
  20. T

    Heat Exchanger

    We suspect that we might need a new heat exchanger for our boiler which is a Vaillant ecoTec plus 428. Can anybody who has experience with this type of boiler tell me how easy it would be for a Heating Engineer to confirm that this is our problem? Also, if it needs to be replaced, what would be...
OFFICIAL SPONSORS

New Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock