You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
end feed
Newline (frequently called line ending, end of line (EOL), next line (NEL) or line break) is a control character or sequence of control characters in a character encoding specification (e.g., ASCII, EBCDIC) that is used to signify the end of a line of text and the start of a new one, e.g., Line Feed (LF) in Unix. Some text editors set this special character when pressing the ↵ Enter key.
When displaying (or printing) a text file, this control character or sequence of characters causes the text editor to show the characters following it in a new line.
Morning all. Just about to install a crosswatwr shower valve and want to connect in the valve with end feed 22mm x 3/4 male. Manual says not to use tapered threads. Cannot find parallel out there that come with end feed.
Any ideas
Thanks
Consisting of quality Endfeed fittings, that are WRAS approved and manufactured to EN1254-1, this pack provides all the fittings you need for standard water and gas application in an easy to handle and store bucket.
CLICK HERE
As in title, what's everyones favourite brand of end feed fittings? Mines are Yorkshire Endex as they have never let me down, and are thicker and much better made than the cheapo brands.
On the cheaper fittings, from the diy chains, not only is the copper thinner, but one end of the pipe goes...
Am sure is not me as I have done end feed fittings before with no problem.
What I am experiencing is that after cleaning up the fitting and the pipe they slip into each other fine but after I apply flux they do not. If I try to turn the fitting on the pipe a lot of the time it is very hard...
I am looking for a good place to buy in bulk end feed and capillary fittings, I have looked at BES but don't think they are very cheap can anyone recommend anywhere please.
Hi All,
First post but I've been reading a few threads on here and love the honest, and sometimes much needed, blunt advice. I hope you can advise...
First off I'm not a plumber (I know, I know) but need to reroute some existing copper water pipes (currently a mixture of 15mm cold and a short...
MarkR
Thread
copper
cross
endfeed
existing
first
fitting
needed
pipes
Had a leaking plate heat exchanger today and found the end feed connection had a gouge on the seat where its been leaking for so long. Tried to replace with a tap connector but they of course have the spigot on them, which wont fit in the hole.
Looks like my only options are:
add solder to...
Bunker
Thread
connector
endfeed
female
iron
leaking
solder
which
135 Piece Endfeed Copper Fittings Trade Pack by Kernow Available at Plumb-Bay know of a similar pack cheaper??? i dont rally want to fork out £104 for the 300 on screwfix, any suggestions? , dont like solder ring by the way!thanks!!!
Whilst recently altering the boiler flow and return to accommodate an underfloor heating manifold I de-soldered some joints and found that there were areas were the solder had not fully run. They were always on the top side of a horizontal joint and although they had not leaked as they were less...
Whilst recently altering the boiler flow and return to accommodate an underfloor heating manifold I de-soldered some joints and found that there were areas were the solder had not fully run. They were always on the top side of a horizontal joint and although they had not leaked as they were less...
davenport.neil
Thread
always
endfeed
heating
horizontal
joint
problem
solder
So I'm looking online, shopping for 22m end feed elbows.
This well known supplier has 2 different sorts, both in pack of 10, both 22mm end feed copper.
One is unbranded for £5.94, the other one is branded FlowFlex and is £3.99.
What the heck's the difference?
Rodolphe
Thread
brands
copper
endfeed
every
fitting
fittings
other
I prefer using end feed type copper fittings and I have had a good success rate.
However, I usually get an ugly drip of solder. Could anyone advise how I could avoid that and make a really neat job?. I know I am being a bit OCD about this, but that's just me!
thanks
tuttogallo
tuttogallo
Thread
color
endfeed
fitting
joint
making
solder
soldering
At 18 pence for a 15mm elbow, this is a good price from a reputable company who I've bought a lot from over time.
Conex - Primaflow - Crosco End Feed Elbow ( Copper Fitting: 15 mm 15mm)
Some good prices for other things too there and for you heating guys, they'll put together a really good...
Hi guys, I've started a new council contract and they don't allow the use of end feed for some reason so I've got 118 mixed 15mm fittings for sale there on ebay, item number 300675167394, if anyone's interested and wants to make me me an offer then please PM me, cheers
i have a couple of little jobs..........(moving 2 rads and fitting new outside tap)
a lot of people say push fit is the way to go. i dont mind having a go at soldering and have aquired the tools to do it.
if i paid a half decent plumber to do the jobs what should i expect to see them using...
Hello, can someone clarify the difference between end feed reducing couplings and reducers. Would i be correct in my assumption that reducers take the pipework internally and reducing couplings take say a compression fitting external to the fitting ? Could someone give me some examples of...
I am a competent DIYer, and I normally use end feeds in preference to solder rings.
I am currently refurbishing our bathroom and I'm chasing the rad tails into the wall to accomodate a ladder rad (I will sleeve them in damp proof material to allow for expansion movement.
Pipework has been...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.