We have recently had water hammer issues. Plumbers have installed an arrestor near our kitchen sink and a device in the toilet cistern to slow water shut off. Worked for a bit, but hammer returned. This morning, while the toilet was refilling and the shower was on, there was a loud thud that...
Hi Guys,
Jus had a quick question, had a customer call me saying there is no hot water or CH and boiler is flashing L8.
Had a look at the MI troubleshooting page which said could be fan error, pcb error or wiring harness. Disconnected the fan connector and was not getting the nominal 330 V DC...
We have 2 Crosswater digital showers with a duo water control system. Last Autumn, one of them started cutting out at the start of a shower 2 or 3 times before finally working ok. It then seemed to correct itself over the winter. However this has now recommenced.
Also during the last 2 weeks...
Hi all,
Heating engineer has curved 15mm ch pipes where the wall meets the ceiling instead of notching the joist further and putting them at a 90 degree angle so completely hidden when ceiling is boarded and wall bonded then plastered. He explained that he couldn't notch out the joist anymore...
Just about ready to fit wall panel over this bracket, instructions say 50mm cut out around pipes, this seems a bit excessive, can anyone advise if i can go smaller than this?
Hi Everyone. I have had a boiler installed in March 2020 (a replacement like for like Valliant boiler). It has cut out twice with F20. Valliant came out and state that I have "All" my rads off so the boiler cut out due to over heating. The thing is that not all my radiators were off, most were...
Hi just wondering if anyone can shed any light on an issue i'm having with my boiler..
Initially started i think after i came back of holiday and the pressure was low on my boiler after topping up everything was fine and boiler operated as normal. A day or so after however i started noticing...
Over the last few days we are having problems with the boiler cutting out after a few minutes.
Hot water seems to be fine (although it may be taking a bit longer than normal to heat up), and the flames are all lit. They remain lit whilst the hot water is running (which is correct).
The...
I was wondering if anybody could possibly confirm if 35mm is the standard size for the cut out hole for a kitchen sink tap? Any help would be appreciated.
HI all..just purchased this bath and haven't come across this recessed rectangle where taps should be.. any help much appreciated?
Thank you in advance..
HI my dad has a problem with his baxi combi 105he, it's been trouble free for around 7 yrs but now appears to cut out before reaching the thermostat temp. The radiators are not getting hot. In summary
1. CH thermostat requests heat, boiler comes on for around 5 mins then cuts out
2. Boiler...
Hi guys.
Been to that stopcock job tonight and the customer has asked me to cut the existing one out and replace.
The pipework will be getting upgraded to copper/mdpe at some point apparently.
Can someone help with the fittings needed? see pics.
The end of the stopcock with no fitting...
Hello All,
today has been one of those days!
arrived to service a potterton profile 100e and found a lot of rust dust in boiler so decided to strip down, remove burner and clean thoroughly.
i reassembled and fired up boiler.
there was a fault evident in that
1- the boiler goes through start up...
Im an electrician and ive been asked to fit a tepcon cylinder stat.
The thing i dont understand is that there were 2 cables going to the old stat.
Can i just use one of the flexs go through common on the cut out, then from number 2 loop to the common on the stat and out of 1 to the load...
This week Potterton Netaheat Profile 80 tripped out and I used the reset button to try and get it going again, but ... it didn't restart until I turned the boiler thermostat down to 0.
Now, if the boiler is cold it will only restart with the boiler thermostat set to 0. As it warms up, the...
Installed yesterday worked perfectly ch and dhw, woke up this morning, ch is perfect but dhw cuts off after approx 2min 30 secs and requires reset which does nothing other than allow me to have dhw for a couple more mins.
Worcester comin out on Monday to have a look but do you guys have any...
Customer rings with intermitent cut out, when i arrive works OK. may have healing hands or i give off static electricity vibes.
anybody experienced this problem.
in fault finding it leads you to gas fault or flue overheat stat.
Hi, I'm gas safe registered.
I went to look at a friends Halstead ace boiler that keeps locking out when there is a high demand on the boiler when on central heating and hot water.
I was thinking it could be the overheat thermostat but I'm not sure.
Going to this prob tomorrow, guy says the heating is working fine but when he uses HW its runs for briefly then cuts out, if he resets it, it fires again for a bit before cutting out. Suspect it could be blocked dhw exchanger, is this common? The jobs far out of town, so was wondering if it...
Hello lads and lasses
Customer has the above boiler. when switched on it runs for around 2min, bangs and cuts out. feeling the flow and return pipes. flow gets luke warm then when boiler bangs and cuts out flow pipe becomes instantly hot. Pump appears to be working, well its making a noise and...
traineedrip
Thread
air
airlock
banging
boiler
ceiling
circulation
cold
cutout
cylinder
dhw
flow
header tank
hot
hot water
motorised valve
motorised valves
noise
pipes
plumbing
potterton
potterton suprima
problem
pump
suprima
system
valve
valves
water
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.