Search the forum,

connections

HCL Connections is a Web 2.0 enterprise social software application developed originally by IBM and acquired by HCL Technologies in July 2019. Connections is an enterprise-collaboration platform which helps teams work more efficiently. Connections is part of HCL collaboration suite which also includes Notes / Domino, Sametime, Portal and Connections.

View More On Wikipedia.org
  1. M

    Flexihose connections

    I have a new mixer tap with 30cm flexitails which are too short but wondered if i can connect another flexihose to it and if so what connections would be required, I was told that a coupler might be required to connect them together any advice on this would be appreciated.
  2. B

    connections to bidet using Geberit frame

    Struggling to make the connection to the bidet. The bidet has a flexible hose connection with a 15mm female end to attach to the Geberit frame. The water take off male connection on the frame looks to be 12mm. Is there a coupler required?
  3. moonlight

    Shower with 1/2 connections

    Before the lockdown. I went to look at a dripping shower, its about 15 years old so I was told. I don't recognise the bar shower maybe someone else might, all it has stamped on it is a letter B it is a thermostatic bar shower but with 1/2 inch connections. The fittings on the shower are half...
  4. M

    Kitchen shower tap connections

    Hi I want to I stall this tap the pipe side is just a screw on type and I want to use a flexible hose, what connections do I need for the tap side . Thanks
  5. Bogart

    Pipework sizing and connections

    Posted a message before about new position for kitchen sink and feed to it. Was told best is mains and not tank, to which I definitely agree. Was going to run a new 15mm cold feed from mains to this tap but as that will involve drilling through quite a few kitchen ceiling joist I wondered if...
  6. Roger of Weston

    Boiler connection 22mm

    I have a 40CDi combi boiler in a 1920s house. The heating does not get hot just warm. I have 22mm from the boiler to under the floor but then connects to original half inch/15mm copper lagged with hessian. I believe I am losing heat as some of the runs are quite long. A local plumber said I need...
  7. R

    Need help with ordering soil pipe connections to lower a soil pipe for a loft conversion

    Hi my bulders have just fit a soil pipe connector to a new loft extension but the soil pipe needs to be lower as it's currently at balcony hight and can be seen wanted to lower in line with the gutter if I can find the right connections hopefully I can lower without too much work ant help would...
  8. centralheatking

    Flexible Connections ...problems

    I hear that all flexi braided connections have been de listed by the NHS. The problem is their rubber core which becomes soft and collects bacteria. This is obviously not good and they have decided to cease using these connections anywhere near hot, cold and drinking water. Wras are already on...
  9. Stigster

    What size are the connections on these valves?

    From a thread where I've been helping someone with radiator valve problems. Looking at the pictures of thes towel rail valves I'm not 100% certain what size the connections are. Pretty sure it's 15mm coming in to the valve but is the rad-side connection 1/2" with a fat nut or 3/4"? If anyone...
  10. C

    Todays Strange Meter Connections

    I may be being really dumb here, come across this today. ECV basically flush with the floor allthough perfectly accessible. then 2meters of lead pipe going out to the regulator through the meter sat on a shelf, then another GSR has piped 22mm away from it obviously in a strange route. Although...
  11. N

    Kitchen mixer tap pipe connections

    Hi New here, so hello to all. I am to replace a kitchen mixer tap which has been in since the house was built 4 years ago. Upon inspection, the plumbing doesn't include isolation valves so I need to cut off all water to the house. Before I go ahead and fit this I want to take the...
  12. S

    Concealed shower connections

    Hi, Looking for advice on suitable connections for a concealed shower. Shower is a dual function Laura Ashley (Roper Rhodes, I believe) - see Clifton Concealed Dual Function Shower System. Valve has 4 ports: hot and cold in, and 2 outs - all 3/4" BSP parallel. 2 shower outlets: elbow (shown in...
  13. T

    Re-using existing connection to a replacement Cylinder

    I'm renewing my old indirect cylinder with a like for like replacement (albeit with an additional shower take off point). I intend replacing the cold feed and boiler connections with new pipe as they are pretty easy to replace. My question is about reusing the existing hot water take off point...
  14. A

    Do you know what these pipe connections are?

    Hi all I moved into a new house last year and under the kitchen sink the pipework has what looks like 2 filter connections but I have never seen these before and having ploughed through the internet I can't find any products that look similar. Even went into a couple of stores including Selco...
  15. M

    Waste Pipe Connections

    Hi Guys Can someone take a look at my sketch please, I’ve got a bath waste going into the stack at 180mm centres to the toilet waste plus the shower waste at 90 degrees to the toilet waste. In the second picture it shows what is permissible. Can someone confirm if I do it to my sketch it will...
  16. C

    Built in gas cooker and hob connections

    Hi .Hoping someone can help .Is there such a thing as a double micro-point self sealing valve to plumb in hob and oven without having to use T pieces and ad another micro-point . Also the hob is over the cooker .Would a metal braided hose be safe too use or does it have to be fixed pipe work ...
  17. R

    Water feed pipe connections... help

    Hi all, I am trying to replace kitchen sink taps at my dad's house and the hot tap connection had a leak. I want to replace current fittings and I wondered if I can do it by cutting the old copper solder ring straight coupler off and put a compression connection on to the pipe that the coupler...
  18. I

    Help identifying sink connections & availability for appliance install

    Hi everyone I am looking to purchase a Compact tabletop dishwasher from currys as shown in the link below http://i66.tinypic.com/qrisyv.png I am not sure if under my sink the connections/valves are there and free/available. I have two colour coded valves, I think the first one is connected...
  19. R

    Problem with rising main tap connections

    Our old mains water tap seized, so we had it replaced a couple of days ago. The original was brass, connected directly to the blue supply pipe, with a smaller outlet going to a pressure control valve with a pressure gauge. The replacement is as shown in the photo. About 40 minutes after it was...
  20. T

    Outside pipework and connections

    Firstly, Im not a plumber but like to tackle anything in my own house. I want to plumb in a USA type fridge to the cold water supply in the kitchen. The floor is tiled and i dont want to lift them. The best route is outside through the kitchen wall under the sink.... under the decking fir...
Creating content since 2001. Untold Media.

OFFICIAL SPONSORS

OFFICIAL SPONSORS

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock