You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
blown
A blown idiophone is one of the categories of musical instruments found in the Hornbostel-Sachs system of musical instrument classification. These idiophones produce sound when stimulated by moving air. For example, the aeolsklavier features sticks while the piano chanteur features plaques.
This group is divided in the following two sub-categories (see: List of idiophones by Hornbostel–Sachs number):
Hi, Two days ago we noticed we had no hot water. We have a mega flow tank/cylinder in our airing cupboard. It appeared that the lack of hot water could not be solved by setting the motorized valve to 'manual' so as to open the valve to allow heated water 'in' having been heated from the...
Hi guys. First post on here. Called out to fault on Alpha HE 33. Fast blow fuse found to have blown. Faulty fan found to be problem. New fan installed and tested. Four days later and a call from customer to say boiler not working again. fast blow fuse found to have gone again. Replaced and gone...
Hello,
I installed 2 compression valve fitting for my kitchen sink about 10 days ago, after I cut off the 2 old valve with pipe. I put teflon tape around the olive after I found leaks from the fitting(which had been proven wrong!), with oil around the thread. It had been working fine until this...
I was removing my room thermostat to paint around, and the earth become loose and blew the fuse to the central heating boiler.
I've replaced the fuse, and the 'power' light is back on my boiler, however the digital reading panel (time, pressure etc) isn't working.
Unsure if the surge has blown...
Had a call out earlier, leak through ceiling from boiler. There was a calmag magnetic filter which had blown completely off the threads which you unscrew to access the magnet. Baffling because id have expected it to be split/damaged.... Screwed it back on,topped pressure ran heating upto...
Hello,
A couple of weeks ago I called out a plumber to change a thermostat since the bottom one (Economy 7) wasn't working. Unfortunately the change hasn't worked and since then (due to cost of calling in the plumber again to sort), I have been using the "Peak" switch for an hour a day to get...
Hi guys,
My parents have a combi boiler which was installed about 12 years ago and has been working fine. The other morning there was a bang and water started pouring out under the boiler.
I went over to help them out and had a quick look, 2 soldered joint on the cold water feed to the boiler...
Ibts
Thread
apart
blown
cold
cold water
fitting
meter
pipes
since
water
water meter
water pipes
glow worm hxi30 boiler f9 fault code. no low water pressure switch on this boiler.and blown fuse second on pcb (does tis mean board gone?) main board
pump external to boiler. grundfos 25-80
slight history of job, arrived to fit dual fuel cooker gas hob electric oven. fitted
connect l.N.E to...
vic66
Thread
before
blown
board
boiler
code
cooker
fault
fuse
glow
glow worm
glow-worm
main
means
oil
pcb
switch
worm
Having problems with above mentioned thermostat. Been running with no issues for 10 years. A jumper fell out today from the back of the control unit, and I must've replaced it incorrectly as when I opened the receiver later on to troubleshoot, I saw that they weren't corresponding. I only...
osh
Thread
blown
heating
help
mains
no heating
power
receiver
salus
Hi, was just wondering if anybody else as had problems with jg speed fit fittings blowing and appearing cross threaded. I have a client that is blaming poor workmanship even though I check and double check for leaks. This is the first time I have had this happen and would generally endorse speed...
I went to a job (y-plan system) where all the stats, motorised valve & the 2 channel prog were dead. The wiring centre was dead too but the spur (where the wiring centre took its perm live) was live giving 235v. I had to leave without fixing it. Anyone had this before? Any advice on what I could...
Hi
I installed an RM 180 lt direct unvented 2 months ago. It serves a deli and kitchen area so the elements are on 24/7.
Saturday both elements faied and took the rcd. Both were blown as you would expect after say a year or so. Spoke to RM and they advised fitting titanium elements due to heavy...
Hi guys
looking for some advice, i fitted a Richmond plus gas fire 2 months ago everything fine, coals placed correct, it was for a neighbour.
Gets a call tonight she says she lite the fire went to the kitchen and heard a noise and came back and coals were on the hearth and the heavy ish fire...
Hi all
I've had my first compression fitting blow off - thank god I was there at the time...It was the cold feed to one of these bar valve fixing kits:
H&C Contemporary Bar Valve Fixing Kit Chrome Effect | Shower Spares & Fittings | Screwfix.com
After examining the pipe, I realised that, even...
Hi again everyone, back with my lovely boiler, engineer came out and gave the boiler a service, got it working all nicely, until today, was working fine this morning and then it cut out, turns out both 3.15A fast fuse and 5A plug top fuse had blow, the 3.15A was literally blown to bits lol, only...
Hi, I wonder if you could help. My Vokera Unica HE boiler suddently stopped working one day. There was no light on the display at all, no error messages, nothing. The display was totally dead. It looked to me like an electrical problem, maybe a blown fuse. I rang for an engineer who came and...
went to do a quote for a builder renovating a 3 bed detached yesterday. first thing i didnt like was the 'theres no money in this job' coming from the first couple of sentences from him.lol
he had took the old boiler off himself and left an open end to the gas main for another!
any way, he...
Hi, I fitted a ball-a-fix valve on the cold feed to the cold water storage tank in October 2011. Lagged all pipes but did not cover the valve. All has been fine - no leaks or problems. House has been empty ever since with heating off. Had a call last week (following temperatures as low as -10 )...
Firstly apologies as I'm a complete novice to boilers....the things not working hence I'm having to learn!
Came home from honeymoon last week to find the boiler wasn't on, no power. Checked the power feed to the boiler and this was fine as was the 3Amp fuse. Oven the unit where the power cable...
JoseGaf
Thread
ace
bar
blown
boiler
boilers
cable
combi
combi boiler
diverter
fed
fitting
fuses
heatline
help
leak
novice
oil
please
power
pressure
problem
seal
steam
valve
water
water leak
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.