You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
assembly
The London Assembly is a 25-member elected body, part of the Greater London Authority, that scrutinises the activities of the Mayor of London and has the power, with a two-thirds super-majority, to amend the Mayor's annual budget and to reject the Mayor's draft statutory strategies. The London Assembly was established in 2000. It is also able to investigate other issues of importance to Londoners (most notably transport or environmental matters), publish its findings and recommendations, as well as make proposals to the Mayor.
Hi, I cannot get the sink assembly out of the sink. There is no nut underneath, it seems the top and bottom of the assembly screw together. It has been in there about 15years I reckon. Any help on how to unscrew it?
There looks to be 4 small recesses inside that you could a tool into and try...
I have a quarter - turn Cold Water Kitchen Sink Tap that has a started dripping and i am trying to gain access to the washer/valve assembly and looking for advice as to where/how as cannot see any obvious screws on the main tap body and the small blue plastic insert does not seem to move...
Hi,
We have a shower like the atatched pic with Bristan 1901 on the cap.
I had an issue with the shower leaking from under the handle and the odd time the water was gushing out.
I contacted showerdoc and bought replacement seals. That didn't seam to work...
Hello,
I am looking on behalf of my installer for a pilot assembly for a spacesaver 60BR Mk11 GC 41-313-56 part no: 429788 any advice would be welcome
bests
Dave
Hello, our shower has started to seep a few drips from the stabiliser valve assembly (P07810800) but not from the top where the plunger is which appears to be where they can normally leak from. I've seen you can buy as gasket kit for this area.
Ours is leaking from where the temperature control...
Hi all
I have a leak from the 1/2” BSP Sensor Pocket Assembly Long of a Megaflo Eco SystemFit Unvented Cylinder.
Any ideas on how to fix it?
regards
Jim
I have a Bristan Easyfit Rio Basin tap assembly, and I have a drip which more than likely means that the ceramic valve needs cleaning or replacing, however after removing the screw in the top of the handle I cannot get the handle assembly off, I'm using WD40 and tapping it gently with a small...
Can anyone point me in the direction of a replacement filling loop assembly for an old Worcester 24cdi Boiler.
Part number on the broken filling loop is 8 716 141 062
GC no. G20 47 311 32
GC no. G31 47 311 33
As it’s an old boiler and in a static caravan a replacement boiler cost would be...
Hi, the sentence in the title is part of the instructions for a Cersanit close coupled toilet, I know that the sentence could not be any clearer but this seems odd to me. Should the cistern be away from the wall? The toilet that I'm replacing was screwed to the wall via two holes in the back of...
I am no plumbing expert so would appreciate some advice. I am replacing the bottom entry inket valve assembly on my toilet cistern. The thread protruding out of the bottom of the cistern is marginally too long to fit to the existing pipework. I don't really want to cut it shorter or change the...
The wife asked me to have a look at the washing machine as it was piddling water all over the floor, checked the waste outlet pipe all was good, checked the rubber water pipes all was good, while I was having a good look at possible splits it pipes or anything I came across a hole in the bottom...
DaveyL88
Thread
assembly
checked
machine
pipes
washing
washing machine
water
Hi
I would appreciate advice as to where I can find a replacement low level Discharge flue assembly for my 1978 Worcester Danesmoor 1519 oil boiler which has almost disintegrated. The boiler is fine so any ideas, please.
The fill on my toilet is very slow, I have found that If I take the lid off the cistern and lift the shut-off arm? and release a couple of times and release I can make it flow faster. There is also water escaping from the top of the fill valve assembly, this continues after the water has...
Need to replace one of these, the one i found on a spares site looks slightly different to the one thats in at the moment. Are the new ones just a different design?
hi guys can i pick your brains? i have a potterton gold combi.
last night the boiler tripped the electric. i found some heating system water leaking from the diverter value- motor unit and assembly.
when i removed the motor unit this morning i found where it fixed full of water which had made it...
This morning when my boiler started it suddenly started leaking hot water and the rcd tripped my house electrics. Upon investigation I found soon I restarted the boiler it restarted leaking from in between the 3-way valve and its cartridge up the top.
I have not come across this before. I am...
In December last year my boiler started to sing so following advice on the forum I replaced the 2 o-rings in the 3 way assembly valve. I replaced the rubber o-rings on the DHW push rod & the CH push rod. This instantly stopped the high pitch noise. I had the left overs of an overhaul kit from...
Hi All
Probably an obvious question to most here, but I have always used a collueges core bit set-up and it is always put together when I use it.
I have just bought my own core drill set (Duradiamond 5 Core Premium Slotted Box Kit). My question is about the pilot bit. How is it inserted into...
Hi - I have changed a leaky diaphram on my Baxi Main Combi boiler. It was the one on the central heating pressure differential valve. It's all gone back together OK except the push rod on the hot water differential valve is sticking out and stopping me from locating the valve onto the valve...
_Chris
Thread
assembly
boiler
chris
combi
differential
diverter
diverter valve
main
really
valve
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.