Search the forum,

Discuss Cast Iron Radiator - External Rust Advice in the UK Plumbing Forum | Plumbing Advice area at PlumbersForums.net

Messages
4
I've spotted this rust patch on the outside of a cast iron radiator in the house.

rad rust.jpg

There's no sign of any water leaking from it on the floor, however when I put my finger on it, I couldn't say it was bone dry.

Any advice on what I should do to try and resolve this? I'm a bit fearful of touching it incase I make it worse and it starts leaking.

Sadly I don't know the make or when they were installed as it was by the previous owner. It should be noted that this is the only radiator that has this patch, the others in the house are fine.
 
Are they in a damp environment?
 
Would say then the rads getting very close to pin holing time to change
 
Is there anything I can do to clean/dissolve the rust and use some sort of sealent for a short to midterm solution? I don't really want to spend a wad of £££s on a new radiator at the moment.
 
I wouldn’t say so as it’s coming through from inside out
 
I did the tissue test today and it definitely doesn't have water coming out of it 🙏 . The tissue only showed a very feint brown colour (from the rust).

How thick are cast iron rads? I'm thinking a solution could be to remove the outer layer of rust to prevent any further spread, then add a primer coat (red oxide) to prevent any contact with the air/moisture.

I'm making a huge assumption this is external rust due to moisture and/or just chipped paintwork from the previous home owner.

Any potential pitfalls with this potential solution?
 
depends if the old cast iron or cast iron effect old ones normally are 0.8-1cm thick cast iron effect 1-3mm etc

Turn the rad valves off before you do anything and then you can get a flap disk for a Dremel or other rt and then remove the rust on top and then use some rust converter and then red oxide prime etc
 
Looking at the photo I'd say it is from within so be careful poking it.
As Shaun said, close the valves first.
If it is from within, there's not a lot you can do with it.
 
It's a temporary measure but after you've cleaned it up (as above), you could patch it with a smear or two of JB Weld epoxy. That should stabilise it for a while.
 

Reply to Cast Iron Radiator - External Rust Advice in the UK Plumbing Forum | Plumbing Advice area at PlumbersForums.net

Similar plumbing topics

60's ranch, with single bathroom. Tile over concrete slab. Toilet is about a foot from exterior brick wall. Vent pipe is in interior wall behind toilet. There's a concrete patio outside the bathroom, that extends about 10 feet from the wall. I'm considering adding an ADU in the back yard, and it...
Replies
1
Views
176
Good evening I've came across 90mm cast iron before and used mcalpine extB (90 to 110 extension) But what I have here kind of bellows out to 108mm internal as you can see in the photos. Is this some sort of conversion to clay which is why their is a bulge? What would be the 'Best' way of...
Replies
5
Views
665
Hi all, We've got a toilet that's been leaking due to a faulty seal with the pan connector. We've had a plumber in to replace the pan connector, but it hasn't done anything to fix the leak (and has cost us over £200). The plumber has told us that it can't be fixed due to the height of the old...
Replies
9
Views
1K
Hullo everyone its a while since I posted on here basically because i have had no plumbing issues however I have one now. My son recently moved into a house which has cellar within which is a radiator which is part of the central heating system. The rad looks old, rusty and horrible as does the...
Replies
3
Views
322
Hi I have recently bought a house which is 17 years old. There was a small leak from one of the radiators So I took the pipe off and drained the radiator and the water was black/brown. I took the radiator off and flushed it out with a hose pipe out the garden but it's got me thinking and I...
Replies
0
Views
301
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock