Users can remove all display ads (not sponsors) for a small fee. Click for info (must be logged in)

Recent content by Tommo25

  1. Tommo25

    Bunging open vented system

    I've not heard of using a carrot, may be worth a try, I'm guessing the carrot will swell slightly to create a better seal
  2. Tommo25

    Bunging open vented system

    question for you veterans, what are your tips and tricks for when you don't get a good vacuum when you bung the tank. (Sometimes its not a round hole, sometimes hexagonal or got little tabs on it preventing a good seal). I've cut an isolation valve in on the outlet in the past, however...
    • Tommo25
    • Thread
    • america open vented system usa vented
    • Replies: 4
    • Forum: USA
  3. Tommo25

    Van organisation motorbike

    Cbr600rr 05, yeah they look decent
  4. Tommo25

    Van organisation motorbike

    I have a transit custom which I use for work (plumbing and heating) but also for taking my bike to track days. Does anyone have any idea how I can keep my van neat and organised? It always seams to be messy. I don't really want any racking because it will make it difficult to get the bike in...
  5. Tommo25

    Hydro block pin hole worcester

    Thanks everyone job done, after dhs sent the wrong part some baxi electrodes (not even close). Luckily city had one on the shelf, heating and hot water back on. Happy customer, and not too bad of a job at all, a lot easier than it looks đź‘Ť
  6. Tommo25

    Hydro block pin hole worcester

    Went to look at a leaking worcester combi 30cdi, and found it has a pinhole/hairline crack in the flow unit hydro block. (LHS bolts onto plate to plate heat ex) Any tips or anything I should look out for when replacing the flow unit (87161063560) I don't do too much work on Worcester boilers...
  7. Tommo25

    Logic plus combi 30 scalding dhw

    Hi I have a boiler to service - ideal logic plus combi 30kw. Customer says when heating has been on for a while and they he runs the hot water the water is scalding hot. Anyone have a any ideas? I was thinking maybe thermister on flow?
  8. Tommo25

    Toilet Cistern Overflowing (Picture Included)

    Replace with fluid master fill valve (brass shank) model.
  9. Tommo25

    Best boiler for old house/system

    Viessmann if you want the best, baxi 600 also good
  10. Tommo25

    Van 6-7k budget - work and motorbike

    I'm looking for a new van, it needs to be big enough for fitting all my plumbing gear in, but also a motorbike. I'm interested in transit, transit custom or VW transporter. For my budget they all seem to have big mileage 110k+. What would you guys recommend?
  11. Tommo25

    Baxi neta tec 33kw combi 133 error

    I’ve changed the electrodes and checked the resistance across gas valve so that should rule the gas valve out, boiler still bringing up fault. It is looking as though it could be the PCB. As it’s an intermittent fault how would I test it? Thanks
  12. Tommo25

    Baxi neta tec 33kw combi 133 error

    hi all, Did a full strip down on baxi neta tec. Customer reported they were having trouble with e133. Boiler was pretty clean over all. Checked CO readings at Max, min and ignition stage all ok. Electrode gap was 2-3 mm too big explained this to customer that it would need to be replaced at...
  13. Tommo25

    Glow worm 15 hxi roaring noise

    Went back today and it went from bad to worse. I spoke to glow worm and they told me find a happy medium and alter the gas valve so that the boiler would not make the noise. With the boiler set to max I started to do so. The boiler then locked out on over heat. I rang glow worm again to explain...
  14. Tommo25

    Glow worm 15 hxi roaring noise

    Cheers lads yeah I’ve spoke to them (glow worm) before and had a cold reception. They talk to you as if your stupid. None of this would’ve happened if they had a proper boiler fitted ... like a viessmann haha. Anyway thanks for the help I’ll report back tomorrow hopefully solved
  15. Tommo25

    Glow worm 15 hxi roaring noise

    Worked for them before, nightmare customer. Should of learnt my lesson with him last time... The manufactures instructions are a bit unclear on the high/low fire. The only way I can see I could of caused it was when I’ve turned the pentameter at the back of the PCB but I’ve returned that to...

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock