Users can remove all display ads (not sponsors) for a small fee. Click for info (must be logged in)

Recent content by robj20

  1. robj20

    Ideal Vogue "Flow/Return Thermistor Fault" again.

    Not even started. That's with all valves fully open.
  2. robj20

    Ideal Vogue "Flow/Return Thermistor Fault" again.

    What difference does that make.
  3. robj20

    Ideal Vogue "Flow/Return Thermistor Fault" again.

    This is what it did this morning when the heating requested a +1c to the livingroom and dining room and a +2c to a bedroom.
  4. robj20

    Ideal Vogue "Flow/Return Thermistor Fault" again.

    This is flow/return at the minute. This is when the gas is off but the pump is still going. 35c flow 34c return.
  5. robj20

    Ideal Vogue "Flow/Return Thermistor Fault" again.

    I have these settings? Currently set to 70%. I think i should also try and balance each radiator at the minute they are all open fully except the bypass rad. Going to be interesting trying to keep the boiler going while i balance each rad.
  6. robj20

    Ideal Vogue "Flow/Return Thermistor Fault" again.

    So which way do i turn it, 0.4? Its difficult with evohome to set it so the boiler is on but then close the rads down, from what i understand i only need the bypass to kick in when only one radiator is on to reduce the pressure. But now having a bypass radiator it shouldnt even be required.
  7. robj20

    Ideal Vogue "Flow/Return Thermistor Fault" again.

    I forgot to mention its Evohome, so all but the hall radiator are fully zoned and automatic. Also uses Opentherm so i have no control over flow temperature. But i do agree with you that in my mind the issue seems to be more that the return temp is the same or very close to the flow temp. Thus i...
  8. robj20

    Ideal Vogue "Flow/Return Thermistor Fault" again.

    Boiler, Ideal Vogue Gen2 C32 Honeywell Evohome with Opentherm. Had Ideal out last year and they changed the thermistor, but this year its doing it again. Strangely same time of year. Suggestions last year from the installer was to remove the Evohome TRV from one radiator to act as a bypass. I...
  9. robj20

    Evohome and boiler issues

    No no control over it anymore, it's rare it is at max it starts of at about 70c then quickly drops to around 50c before dropping to around 30c and below.
  10. robj20

    Evohome and boiler issues

    I don't have zone valves each radiator is a zone. That would work yes but also means the hall then couldn't call for heat independently. Evohome controls the flow temperature automatically. The dial on the boiler is disabled.
  11. robj20

    Evohome and boiler issues

    I have had an idea. Not sure if its possible though. Can i remove the TRV valve from the hall radiator, fit a lockshield in its place. Then i could run that pipe to the cupboard under the stairs (about 1 meter away) where i can have a HR92 on a the TRV valve to control the radiator remotely...
  12. robj20

    Evohome and boiler issues

    Too late for that now though. Any input regards Ideal response. "Ideal have said I should try the bypass set to 0.4 if it is currently set to 0.3. Does that increase the flow through the bypass or decrease." I suppose when it was fitted they just set it to the middle, maybe its flowing too...
  13. robj20

    Evohome and boiler issues

    What do you mean by trim trvs. I think the bypass radiator is the easiest option until boiler makers make the boilers work properly with fully zoned systems.
  14. robj20

    Evohome and boiler issues

    I did see that 10% of the heating demand. What I might end up doing is having my yet to be fitted bathroom radiator on dual lock shields. Put a thermostat in there so it can call for heat. The only downside is that the bathroom could end up over heated, but that's less of an issue for a bathroom...
  15. robj20

    Evohome and boiler issues

    I cant seem to find a graph for my boiler Ideal Vogue Gen2 Combi C32. There are two settings for the pump as well in the boiler menus i'm unsure which i should have it set to if it even makes a difference. Comes under Pump Modulation 70% (equivalent to 6m head) and 100% (7m head) The boiler does...

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock