Search the forum,

Recent content by Best

  1. Best

    Any ideas?

    If you have a plumber, then seems they know nothing about gravity hot water systems. On looking at the photos, I think you have 2 hot outlets - the usual hot outlet horizontally from top of cylinder with vent, plus you have a second separate hot outlet at left side of cylinder (immediately...
  2. Best

    Loss of Hot Water Pressure to Shower

    Just reread your post and I see you said you checked feed to shower and it was poor flow. Maybe a valve in-line to shower valve somewhere and blocked?
  3. Best

    Loss of Hot Water Pressure to Shower

    Shouldn’t be an airlock as mains pressure at 3 bar will easily blast out any air. Check valves in shower valve or built in filters perhaps faulty or blocked with debris? Hot water pipework filters particularly likely to have blockages
  4. Best

    Electric shower problem

    Maybe a blockage or the shower is faulty - not having all elements working (which would mean very poor flow when achieving suitable hot enough temperature. Check you have cover on correctly with temperature & flow spindles and knobs in proper position - ie, fully on for hottest temperature etc...
  5. Best

    Rattling noise from the valve thing

    It is a bypass valve, the purpose of which is to open automatically, but only when needed to create a bypass. They can sometimes begin to create a noise. Best to get it checked out or possibly replaced as it needs to be at a fixed setting so to open only when system needs flow through it...
  6. Best

    AGA Going out after 12 to 36 hours

    Do you have the Aga properly serviced? Maybe stating the obvious points but my first thought would be the steel pipe feeding the Aga burner gradually narrows with carbon & has to be carefully cleaned, literally drilled out each yearly service. The wicks not as important, but need to be replaced...
  7. Best

    Green copper pipes, plumber didn't clean up flux after job

    Never did try to scare the OP Ric! But I wouldn’t take any old excuse or lies from anyone responsible for something I am paying for. Flux on all pipes is a tell tale sign of careless work. We wouldn’t accept a painter to leave paint splattered over floors or windows would we? I have seen flux...
  8. Best

    Green copper pipes, plumber didn't clean up flux after job

    If he does say that flux isn’t corrosive, - ask him is it okay then if you do him a favour and paint his van wheels with same flux to ‘protect’ them from corrosion. Lol!
  9. Best

    Green copper pipes, plumber didn't clean up flux after job

    I suggest leading the plumber into admitting he is in the wrong by asking him - Is flux corrosive? Hopefully he will reply, Yes, and then gives you the opportunity to say politely “That’s what I thought, so I cleaned all the flux off those joints after noticing it.”
  10. Best

    Green copper pipes, plumber didn't clean up flux after job

    As above posts, ^^ no pride in his workmanship
  11. Best

    Heatslave greenstar II 18/25 duel oil feed

    Polite reply here, but firstly stating the obvious maybe, - second hand boilers are a big risk and will require overhauled. I hope you paid little or nothing for it. Secondly, - since you have no idea about connecting the oil pump, you obviously won’t have the know how to install and commission...
  12. Best

    What type of system do I have?

    You have an unvented hot and cold water system. Your heating system is a sealed system (as it has no small feed tank in attic to fill it). The Megaflo cylinder will be ideal for you as it gives better flow rates of hot water than a combi boiler would. Perfect for larger homes with 2 or more...
  13. Best

    What type of system do I have?

    That Megaflo is a hot water cylinder that is stainless steel unvented and therefore allows you storage of hot water, unlike a solely combi gas boiler system. It has same benefits that a combi system has (balanced high pressure to hot and cold throughout the house) but better flow rates of hot...
  14. Best

    Central heating clicking noise. New install

    Sounds like a problem with the valve actuator slipping, but easy way to have it tested is if the plumber disconnected the power to valve and test with valve open briefly
  15. Best

    Fire Valve requirement

    No outside walls to their own property? Not a lot you can do then I guess. Would be interesting to know what OFTEC or building control would recommend. Oil suppliers my area I think do have capability to supply to oil tanks 100metres fill hose, although most I have seen would need much less...
Creating content since 2001. Untold Media.

OFFICIAL SPONSORS

OFFICIAL SPONSORS

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock