Search the forum,

Discuss Wet vacuum advice? Mid budget up to £100 in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Hi everyone! New to the site and the forum. I have a question, can you recommend a decent wet vac? Is wickes one the best option out here?
 
I have the Wickes and it's the most basic machine but I just use it for wet with just the hose end for spills etc. If you intend to use it for both wet and dry and want or need better quality tools with a larger capacity I'd consider the other recommendations.
 
I bought the Henry version but I use it just for heating and water if I ever have to work on anything nasty like a Saniflo I factor a cheap wet vac back into the quote
 
Big chrome titan from Screwfix. Wheels broke almost immediately. Love the thing. His name is R2D2

Funny story - I watched a young labourer sweep up a load of ground concrete. He then went to hoover it up. He put the hose into the wrong hole on the hoover. The other hole does not suck. You know what it does.

POOF!

The room disappears in a grey coloured whiteout.
 
If you are going to get the titan from Screwfix be aware the lid/motor unit is not held on tightly so when carrying it with a ltr or two of fluid if you bump it the motor unit & can will seperate & the fluid will spill out.

When it has more fluid in it than that the weight holds it locked.

As mentioned above it sucks like a pro... and can usually recover the fluids spilled when carry it partially loaded apart from when the customer has white/light carpets.... apparently...

I still have mine despite a couple of spills in houses when carrying it & a few times when it tipped over in the van after a long day when i forgot to fully empty it out prior.

Also have a older Einhell wet vac which has none of the above issues of detachment of top motor unit from bottom can.

Hope this helps,

Andy
 
I have the wicked one. It's about 5 years old now and still going strong just a bit wobbly now as I've lost a wheel. I only use it for wet as I can't be bother to keep changing the filter etc.
 
Trufax. Luckily only blew a bit out as was only just under the surface of the "fluid"
It was a wetvac with 2 sockets for the hose - suck and blow. In my haste I picked blow.
 
I have the Titan one from screwfix too, it's great. I played about £40 for the smaller one I think. I mainly bought it just for dry stuff but needed to get some water out of some central heating pipes and remembered it was a wet vac too, it made the job so easy.

The only thing you have to make sure is it's properly dry before you put the bag back in otherwise it'll go soggy and split
 
I have the wicked one. It's about 5 years old now and still going strong just a bit wobbly now as I've lost a wheel. I only use it for wet as I can't be bother to keep changing the filter etc.

Don't need to Millsy, it'll still suck up dry material with the combi filter. Just leaves a bit of a mess to empty.

When I bought mine it was £25, now it's over £40 the other wet n dry's available come into play for value for money.
 

Reply to Wet vacuum advice? Mid budget up to £100 in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
Replies
0
Views
88
Hi all Noticed bad smell in my drain out side put my hand down and it unclogged it for now however I checked my sewer drain and after flushing my toilet a good few times nothing is going to the sewer so don't know is there a blockage or what way it works many thanks and advice would be grateful
Replies
3
Views
259
Hi, I have an old steel water mains pipe (approx 45mm) that I need to connect to a new pehd water mains (25mm). I can't get at it to create a new thread so what's the best way of connecting the two? Cheers, Peter
Replies
2
Views
123
My son has an apprenticeship interview for to become a plumber and heating engineer. The have said there will be a multiple choice exam for this for suitability. The thing is my son panics during tests/exams. Is there any book I can buy him to practice the multiple choice test for the exam? What...
Replies
3
Views
262
Hi. I need a new toilet supply line but don’t know the size type of the fitting at the shut off valve. It is not 3/8 compression. It is a plastic nut about the same size as the one going into the cistern but has a different thread. Attached is a photo. Can you advise. Thanks.
Replies
2
Views
161
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock