Questions and plumbing advice in the Bathrooms, Showers and Wetrooms - .
Some popular plumbing forums: Plumbing Advice - Plumbing Tools - Plumbing Courses & NVQ's
Hi advise on the best anti mould white silicone for around bath, I know none will stop it completely
Hi..
I am after advice on installing a bidet in a toilet with the water valve hidden inside the cistern.
I am renting. Is there anyone with a creative way to go about this without drilling the cistern?
If that doesn’t make a lot of sense, let me know and I will add a photo.
Thank you very...
My builder has fitted 14 Triton Showers to a block of flats which I let out, they are manager by a letting agent, I am now getting complaints that the pressure relive valve is operating and the agent informs the Plummer who changes £80 to fit a new £5 pressure relive valve
HOW CAN I modify...
Good evening
I've came across 90mm cast iron before and used mcalpine extB (90 to 110 extension)
But what I have here kind of bellows out to 108mm internal as you can see in the photos. Is this some sort of conversion to clay which is why their is a bulge?
What would be the 'Best' way of...
Good morning! First post looking for advice on an issue I am having with a bath installation. Although I have installed many baths before, mainly using perimeter battens for support, I am attempting to install a fancy whirlpool/jacuzzi bath for my son. Plumbing and electrics are sorted but my...
Hi, I have just tried to repair a very old Mira 8 shower unit. However, when trying to remove the brass cover plate it's completely scaled up and it won't budge any ideas on how to free it up. We did think about trying to heat up the bass cover plate but we are concerned about the silver outer...
I’m after some replacement roller wheels, not necessarily the whole roller units. The shower unit was made by Biava - pretty old, around 20 years, I should imagine. It doesn't look like parts are easily available as I've looked pretty hard and contacted a number of online sellers.
Some of the...
My toilet has been randomly doing a small flush. I've had a visit from a Saniflo engineer who has checked the unit. There is no blockage and it is flushing away correctly.
He has replaced the non return valve and the solenoid valve but this has not solved the problem. There is a very slow...
Hi All
Just looking for some advice on which Exposed Thermostatic Mixer Shower (Bar Shower) would go well with the Shower Pump i'm getting installed.
So the pump is the - SALAMANDER PUMPS CT FORCE 30 SU REGENERATIVE SINGLE SHOWER PUMP 3.0BAR from ScrewFix - seems like a decent one for the...
Hi,
I hope to adjust the shower mixer tap temperature by adjusting the physical device regulator, that goes by several names/terms. I have experience of this with sink/basin mixer taps and that was straight forward. I have attached four images and seek assistance to identify what they are. Some...
Hi all
Can anyone give me guidance as to how I can get into this tap to repair it?
Many thanks
Dave
Hi - I want to replace Aqualisa power shower to mixer shower to a std. mixer shower, however, the centres for the hot and cold are only 65mm. I’ve tried finding something that would be compatible but no joy. Ideal would be a mixer head with the same centres. Does anyone have any idea as to...
Good morning,
I have a hinged shower screen for my bath that I don't have fixings for.
The guide holes in the screen line up with guide holes in the frame - but the holes in the frame are horizontal slots, presumably so that I can adjust the shower screen for a not-quite-vertical wall.
However...
What is the recommended way to conceal a 1.5M, 40mm shower waste pipe? We have 30mm gap behind the plasterboard which will be renewed. Would you chase the block 10mm or go into the concrete floor?
What are the safety concerns of doing either?
Thanks.
I'm in the process of refurbishing my bathroom. I'll be replacing the existing bath with a walk in shower. Will be installing a thermostatic mixer valve fed by mains on the cold side and a combi boiler (Logic Combi c30) for thr hot.
Ideally what I'd like to do is have the mixer valve at the...
I live in the UK and I need to buy a shower door to fit in a 915mm gap between two walls of my shower room. Most 900mm shower doors available here have 30-to-40mm inward adjustments to fit in a space that is slightly narrower than 900mm, or to address wall unevenness, but not outward...
Hi, I am trying to help my mother in law by renovating her bathroom for her as it was in quite a sad state. The bathroom is a very poor attempt at a bedroom to bathroom convertion. So bad that it still had carpet over the whole floor, the area around the bathtub has no waterproofing what so...
They appear to be acrylic heads.
Hi
I've had to cut hot and cold feed to re route for bathroom feeds.
The 22mm Copper pipe hot feed is slightly smaller then my 22mm Copper.
Solder fittings just slip over it and are really loose so I gather this is old imperial pipe, so I shall use a 3/4 to 22mm coupler.
However on the...
We've recently had to replace a tap which had a persistent drip and now need to replace a shower as it has water coming out the fittings and is very hard to turn off. We know that these fittings are only 4 years old, is it normal for these issues to arise after this time period or could this be...
Creating content since 2001. Untold Media.
Tags
Newest Plumbing Threads
-
Trying to source a dual-flush valve
- Started by Thomas J Marshall
- Replies: 2
-
-
-
-
What constitutes a Commercial Appliance and thus a Commercial Kitchen?
- Started by FozzieBear
- Replies: 3
-
POTTERTON PROMAX 28 COMBI Boiler - Hot Water Issue
- Started by boiler101
- Replies: 4
-
Hole in copper pipe, solder under floor, T coupling & protection- Started by dreikher
- Replies: 0
-
-
-
-
-
-
-
-