I managed to get the broken shower waste body out of the trap. I'm about to fit a new waste, a much more robust brass item.
The trap has a big rubber gasket designed to sit flush against the underside of the shower tray.
Is it a good idea for me to fit a rubber gasket between the flange on...
My shower had previously been repaired really badly before I moved in. The plastic retaining collar on the waste had broken off. Instead of repairing it properly and replacing the waste with a new one, someone used bathroom sealant to hold the trap in place and just plonked the broken collar on...
Hi there. I'm new to this forum, and just looking for some advice. We have just had a new bathroom and have gone for mixer taps on the bath, but I have noticed that when the hot tap is in the off position the tap lever is not facing straight ahead, it is turning in, and it's gradually turning...
Hi,
I am struggling to find what these two cartridges / parts are anywhere. I bought this set from eBay around 2 years ago and the seller has since deleted their account so I cannot get in contact to ask them.
I have asked other sellers who sell the same item but they do not sell parts and did...
Hi all
I'm a female plumber, so don't much encounter a urinal (especially as I usually only do domestic work).
I've been sent pics of something that has broken in a urinal - it's the flush valve. As I gather, the urinal cistern fills up gradually, and flushes through every so often.
A link...
Hello Everyone
I am replacing an all in one shower arm and 200mm square showerhead a head has fallen off and I had to remove arm.
I want to replace with a 300mm head like this.
https://www.NoLinkingToThis/p/cooke-lewis-adjustable-ultra-slim-square-shower-head-chrome-300mm/5882t
I have now been...
Over the last 12 months we have experienced a recurring problem with Mono Block Mixer taps fitted to a bathroom wash basin, basically since he had a new Worcester Combi Boiler fitted, which inluded a filter on the supply side..
I changed the original tap as the operation of it changed and it...
Hi all,
Shower was installed 3 years ago when I bought this place. A combination of below average workmanship and poor tiles (didn't get same batch numbers) has left me disappointed with the ensuite.
Ideally, I'd get it re-tiled, but I fear this will be very expensive, and possibly mean I'd...
I have an electric shower which worked perfectly until my neighbours built an extension. Since then my water pressure is constantly fluctuating which has caused problems with the shower. The temperature of the water can be perfect initially but will suddenly change and I’ll either be almost...
I took out a bath. And Now want to do a wet room can I put tiles on the plywood after I have Waterproof it for the walk in shower or I need tray for the ties. Or does a cement board do the same job thanks to anyone that replys
Im planning on how to fit a concealed shower valve into a paramount wall which has a narrow cavity depth(35mm)
Luckily the rear face of the wall is in the hw cylinder cupboard so i plan to have part of the valve coming through to the cupboard then boxing it in.
If i do this the position of the...
Hi I have a 32kv combi boiler in my cellar, I am switching to a mixer shower from a cold water feed electric. Do I need to fit a booster pump in my bathroom. Or can I fit one using a combi boiler.
Any help would be appreciated
Just mocking up what fittings to use for my shower valve to see that its not possible to fully fit an elbow to the hot inlet as it is fouled by the outlet boss.
I can fit a straight connection and elbow instead but just wondering if its actually the wrong fitting that ive picked? And its only...
I have discovered that the flexible connector from the WC pan to the soil pipe does not have all the "fins" pushed in and is weeping - that's easy to fix - but I'm wondering if I can address another issue at the same time while I have all the cabinetry off.
There does not appear to be any...
good morning
I’ve got a triple shower valve. The cold flow is fine, but There’s just no pressure of flow from the hot.
looking at the valve the silver part is stopping the valve rotate any more left which is the way for hot.
is that why I don’t have much hot? the kitchen taps are fine...
Hello. I've just started to do some ground work for a full bathroom refurb in my house. I'm looking at replacing the current laminate flooring with a tiled floor. Looking under the floor I've found that the area under my bathroom seems to be from where all other pipes branch from. All the...
Hi,
I'm replacing an old concealed shower mixer valve which dripped. Trouble is the pipe inlet spacing is fixed at 130mm and the outlet pipe sits in between the two behind a wall panel. Finding an exact match for the pipe spacing is proving a challenge, but I've come across a few which can be...
Hi, we have a rectangle three walled tiled shower with acrylic base that is leaking in both corners - was only built approx two years ago so really not wanting to replace. So far have had the original plumber and tiler look at it but couldn’t find the source of the leak. Silicone where the tray...
Moving into a 2.5 story new build with combi boiler. Have requested a thermostatic shower in the top floor en-suite bathroom. Developer has advised that it would be better suited to an electric shower because pressure for a thermostatic shower would not be good. Any advice? Not keen on having an...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.